Z3X oppo f9 pro flash error help me team...

Z3X Team

rizan

Active Member
Sep 4, 2018
40
9
Skype
rizan.gpg
Selected model: OPPO CPH1823 (Oppo F9)
Operation: Flash (Download only)
Software version: 2.5

Parse scatter file... OK
Load Rom Images... OK
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM85 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0788
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM85 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xC527089E, 0xF12CA7AE, 0x4A8ADB92, 0xF1F1C8C7
Get Chip ID... [MT6771]
Get SOC ID... [8FF1A6C642E847427935F0C0A36FAD5EBA0ABA8D0094C2244A2FDDBE78F541C3]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [20]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A484347386134A51E1B1439A5C1
Load EMI config from preloader... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x90014A484347386134A51E1B1439A5C1
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000039000 (228.00Kb)
EXT_RAM : 0x0180000000 (6.00Gb)
Get scatter info... OK
Check USB status... USB_HIGH_SPEED
Get scatter info... OK
Verify scatter file... OK
Do NAND BMT remark... OK
Setup download info... OK
Get partition table catagory... OK [GPT]
Read mirror partition table... OK
Generate mirror partition table... OK
Download mirror partition table... error(STATUS_CHECKSUM_ERR)
Flashing done!
 
  • Like
Reactions: mayay03
Top