radmi note 7s can't flash

[kabirsoft]

Operation : Flash
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : HS-USB Diagnostics 9008 (COM15)
Driver Info : Mobile, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1C00800 [8996] 00000000
OPK_DATA : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Preparing Loader...Done
Sending Loader [RedmiNote7_Lavender]...Done
Executing Loader...OK
Detecting Chip Type...OK
DebugData : BAAAABAAAAANAAAAAQAAAA==
Using Alternate Method...
DebugData : BAAAABAAAAANAAAAAQAAAA==
Error getting Payload Information!
Error Log : BAAAABAAAAANAAAAAQAAAA==
Please use correct loader and check USB port / cable.
Operation Finished.
QcFire Ver. 5.6

whats problem

 

[perata]

hi
try write firmware in fastboo mode

 

[kabirsoft]

same problem

 

[perata]

same problem

Upload a screen shot of the error in FastBoot mode

 

[kabirsoft]

Operation : Flash
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM15)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.1.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1C00800 [8996] 00000000
OPK_DATA : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_022]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : MSM8996, eMMC, 64 GB
LU Count : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [vbmeta.img] -> [vbmeta] ...Failed
Operation Finished.
QcFire Ver. 5.6

 

[perata]

Operation : Flash
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM15)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.1.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1C00800 [8996] 00000000
OPK_DATA : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_022]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : MSM8996, eMMC, 64 GB
LU Count : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [vbmeta.img] -> [vbmeta] ...Failed
Operation Finished.
QcFire Ver. 5.6

You are still trying to flash the phone in Qualcomm HS-USB QDLoader 9008 mode try in fastboot mode
If the same problem remains, try XiaoMiFlash