Help rmx1911 realme 5 dead solution...plz help

deepanshu_ag

Active Member
Jan 13, 2019
20
3
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-6784
Boot version: 1.04, FW version: 1.12 (Jun 7 2018 00:06:47)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 48MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: DD68MB (0x444436384d42), rev: 0x02, serial number: 0x0857C832
Manufacturing date: Jun 2019
CID: 15010044 4436384D 42020857 C832661C
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 29.12 GiB(31,268,536,320 bytes)
Cache size: 64 MiB
Hardware reset function: 1
Partition configuration: 0x38
No boot acknowledge is sent (default)
User area is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked

ANDROID System Info:
platform: trinket, cpu abi: arm64-v8a
manufacturer: realme
board: trinket, name: RMX1911
brand: realme, model: RMX1911
build model list: RMX1925, RMX1911
build id: PKQ1.190616.001, version: 9 Pie (RMX1911EX_11_A.13)
build description: trinket-user 9 PKQ1.190616.001 eng.root.20190910.000534 release-keys

Internal storage: 50.70 GiB
Custom moviNAND command is not supported for this device(MMC51).
Detected: SAMSUNG moviNAND KMDD60008M-BXXX/32G





after clear master or frp....phone is show only 9008 port
 

msibashankar

Product Supporter
Sep 27, 2017
214
391
india
PayPal
msibashankar
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-6784
Boot version: 1.04, FW version: 1.12 (Jun 7 2018 00:06:47)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 48MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: DD68MB (0x444436384d42), rev: 0x02, serial number: 0x0857C832
Manufacturing date: Jun 2019
CID: 15010044 4436384D 42020857 C832661C
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 29.12 GiB(31,268,536,320 bytes)
Cache size: 64 MiB
Hardware reset function: 1
Partition configuration: 0x38
No boot acknowledge is sent (default)
User area is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked

ANDROID System Info:
platform: trinket, cpu abi: arm64-v8a
manufacturer: realme
board: trinket, name: RMX1911
brand: realme, model: RMX1911
build model list: RMX1925, RMX1911
build id: PKQ1.190616.001, version: 9 Pie (RMX1911EX_11_A.13)
build description: trinket-user 9 PKQ1.190616.001 eng.root.20190910.000534 release-keys

Internal storage: 50.70 GiB
Custom moviNAND command is not supported for this device(MMC51).
Detected: SAMSUNG moviNAND KMDD60008M-BXXX/32G





after clear master or frp....phone is show only 9008 port
brother chek clk ohms value if it 40 -70 ohms then its correct if it show wrong
then remove clk u can short both jumper then try to set on

share image

plz like thanks
 
Reactions: DEEN ALI

mobilecarekgf

Member
Nov 24, 2019
8
2
RMX1911 after factory reset set dead, tried full dump no success, then made jumper for clk now set is on but imei 0
whats the solution
 

DEEN ALI

Junior Member
Jan 9, 2020
2
1
Realme5 RMX1911 DEAD AFTER OUT ISP CONNECTION
SET COME WITH PATTERN LOCK I HAVE CONNECTED MY PHONE WITH ISP WITH GOOD SOLDING WITH JUMPERS BUT CANT IDENTIFY IN UFI ERROR VVCQ VVC JUST REMOVE ALL JUMPPERS AND CHECK MY PHONE DEAD NOT TRUN ON AND NO CHARGING THEN I HAVE SHORTED MY CLK POINT BUT NOTHING HAPPEN

THEN
RECONNECT WITH ISP CLICK ON IDENTIFY ITS( FAILED To Read ....EXT CSD..)
ANYONE CAN SOLVE THIS
PLZ ITS VERY URGENT
Anyone can come back my phone life thanks in advance
 
Reactions: Ramnarayan

jugnu9523

Junior Member
Dec 4, 2019
4
0
Realme5 RMX1911 DEAD AFTER OUT ISP CONNECTION
SET COME WITH PATTERN LOCK I HAVE CONNECTED MY PHONE WITH ISP WITH GOOD SOLDING WITH JUMPERS BUT CANT IDENTIFY IN UFI ERROR VVCQ VVC JUST REMOVE ALL JUMPPERS AND CHECK MY PHONE DEAD NOT TRUN ON AND NO CHARGING THEN I HAVE SHORTED MY CLK POINT BUT NOTHING HAPPEN

THEN
RECONNECT WITH ISP CLICK ON IDENTIFY ITS( FAILED To Read ....EXT CSD..)
ANYONE CAN SOLVE THIS
PLZ ITS VERY URGENT
Anyone can come back my phone life thanks in advance
Koi solution mila iska same condition my phone plz help any one expert
 

Ramnarayan

Member
Aug 4, 2019
9
3
Realme5 RMX1911 DEAD AFTER OUT ISP CONNECTION
SET COME WITH PATTERN LOCK I HAVE CONNECTED MY PHONE WITH ISP WITH GOOD SOLDING WITH JUMPERS BUT CANT IDENTIFY IN UFI ERROR VVCQ VVC JUST REMOVE ALL JUMPPERS AND CHECK MY PHONE DEAD NOT TRUN ON AND NO CHARGING THEN I HAVE SHORTED MY CLK POINT BUT NOTHING HAPPEN

THEN
RECONNECT WITH ISP CLICK ON IDENTIFY ITS( FAILED To Read ....EXT CSD..)
ANYONE CAN SOLVE THIS
PLZ ITS VERY URGENT
Anyone can come back my phone life thanks in advance
[/Q