sm-j400f can't enter to download mode or recovery after boot repair with jtag plus

arshadn05

Member
Jan 25, 2018
9
3
kerala
sm-j400f can't enter to download mode or recovery after boot repair with jtag plus. when it POWER ON just logo flashing and display off . below afre information

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 18 MHz
CMD Pullup Level: 489 mV
CMD Active Level: 1708 mV
EMMC Device Information :
EMMC CID: 150100514536334D42007F8FDA683557
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 7F8FDA68 , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 3/2018
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 2 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_7F8FDA68_20200523_115029.extcsd
EMMC Init completed.

Operation: Write by vendor (Samsung)

Creating GPT-partitioninig
Writing PrimaryGPT at address: 000000000000
Writing BackupGPT at address: 0003AB3FBE00
Writing PIT at address: 000000004400
GPT-partitioning done

Unpacking file: cm.bin
Unpacking Lz4: cm.bin.lz4
Unpacking file: sboot.bin
Unpacking Lz4: sboot.bin.lz4
Unpacking file: param.bin
Unpacking Lz4: param.bin.lz4
Unpacking file: boot.img
Unpacking Lz4: boot.img.lz4
Unpacking file: recovery.img
Unpacking Lz4: recovery.img.lz4
Unpacking file: modem.bin
Unpacking file: system.img
Unpacking Lz4: system.img.lz4
Unpacking file: vendor.img
Unpacking Lz4: vendor.img.lz4
Unpacking file: odm.img
Unpacking Lz4: odm.img.lz4
Unpacking file: cache.img
Unpacking Lz4: cache.img.lz4
Unpacking file: userdata.img
Unpacking Lz4: userdata.img.lz4

Partition name: CM
Filename: cm.bin , Offset: 000000000000 , filesize: 2183696 bytes
eMMC switching to ROM3
Erasing partition...
Writing partition...
Done writing partition. Write speed: 664.10 KB/s
Partition name: BOOTLOADER
Filename: sboot.bin , Offset: 000000000000 , filesize: 1602064 bytes
eMMC switching to ROM2
Erasing partition...
Writing partition...
Done writing partition. Write speed: 628.11 KB/s
Partition name: PARAM
Filename: param.bin , Offset: 000003500000 , filesize: 962560 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1064.01 KB/s
Partition name: BOOT
Filename: boot.img , Offset: 000003D00000 , filesize: 18825760 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 2012.31 KB/s
Partition name: RECOVERY
Filename: recovery.img , Offset: 000005D00000 , filesize: 22489632 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1999.65 KB/s
Partition name: RADIO
Filename: modem.bin , Offset: 000008300000 , filesize: 34070768 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 2009.58 KB/s
Partition name: SYSTEM
Filename: system.img , Offset: 00000E800000 , filesize: 2408398332 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 3368
Done writing partition. Write speed: 1959.85 KB/s
Partition name: VENDOR
Filename: vendor.img , Offset: 0000AB000000 , filesize: 162195816 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 881
Done writing partition. Write speed: 1892.96 KB/s
Partition name: ODM
Filename: odm.img , Offset: 0000B7800000 , filesize: 138631364 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 526
Done writing partition. Write speed: 1928.14 KB/s
Partition name: CACHE
Filename: cache.img , Offset: 0000CA800000 , filesize: 5800084 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 10
Done writing partition. Write speed: 2008.60 KB/s
Partition name: USERDATA
Filename: userdata.img , Offset: 0000D9D00000 , filesize: 1400033548 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 1044
Done writing partition. Write speed: 2004.81 KB/s

Partition EFS : formatting as EXT4. Please wait ...
Formatting completed

Operation: Writing BootConfig ...
Reg: 179 Value: 0x48
Reg: 177 Value: 0x01
Reg: 162 Value: 0x00
Done

All done time: [00:43:38:912]
 

cellularmaster

Moderator
May 22, 2020
30
92
Canada
Was the device damaged by programming? For this reason you have used JTAG ?.
Or basically you have received the phone already dead ?
 
Top