ASUS ZENFONE MAX PRO M1 (X00TD) HANG ON LOGO SOLVED BY UMT
READ INFO
FLASH
FRP RESET
READ INFO
FLASH
FRP RESET
ASUS ZENFONE MAX PRO M1 (X00TD) HANG ON LOGO SOLVED BY UMT
- Thread starter Forum Supporter
- Start date
hi
Put your problem on a separate topic next time
Phone info is required to find the appropriate flash
What a problem with the phone
I flash another firmware I m not flash with this firmware.
Be careful first read firmware info then choose correct firmware for flashing.
Otherwise set stuck-blinking or dead.
After 44 days letter u give here firmware.
Eltolits
Member
- Dec 28, 2019
- 10
- 0
Eltolits
Member
- Dec 28, 2019
- 10
- 0
Operation : Flash
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM6)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1C00C00 [8996] 00000000
OPK_DATA : 2C58A12EBD1022BD5DBD5D937D1E2451092F62C202525FFCF06EB106DBF93155
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_019]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : MSM8996, eMMC, 64 GB
LU Count : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [xbl.elf] -> [xbl] ...Failed
Operation Finished.
QcFire Ver. 6.2
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM6)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1C00C00 [8996] 00000000
OPK_DATA : 2C58A12EBD1022BD5DBD5D937D1E2451092F62C202525FFCF06EB106DBF93155
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_019]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : MSM8996, eMMC, 64 GB
LU Count : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [xbl.elf] -> [xbl] ...Failed
Operation Finished.
QcFire Ver. 6.2
Eltolits
Member
- Dec 28, 2019
- 10
- 0
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 8 bit (HS SDR 24MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: HCG8a4 (0x484347386134), rev: 0xA2, serial number: 0x479B605F
Manufacturing date: Jun 2018
CID: 90014A48 43473861 34A2479B 605F65D0
CSD: D0270132 8F5903FF FFFFFFEF 8A400026
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 58.24 GiB(62,537,072,640 bytes)
Setting predefined EXT_CSD config: Qualcomm(generic).cfg... Done
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 8 bit (HS SDR 24MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: HCG8a4 (0x484347386134), rev: 0xA2, serial number: 0x479B605F
Manufacturing date: Jun 2018
CID: 90014A48 43473861 34A2479B 605F65D0
CSD: D0270132 8F5903FF FFFFFFEF 8A400026
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 58.24 GiB(62,537,072,640 bytes)
Setting predefined EXT_CSD config: Qualcomm(generic).cfg... Done
rockshafeeque
Member
- Jun 11, 2019
- 11
- 7
send anoder link
rockshafeeque
Member
- Jun 11, 2019
- 11
- 7