Help c7000 after factory reset, frp and efs backup now not detecting!

[atstech]

@all i have a samsung EFS c7000, which had oem lock on and frp on and was not letting me flash or unlock frp due to locks, so i thought of doing it thru isp,
it connected fine and i did all operations, but after im trying to switching n nothing and isp also not detecting at all!
pls lee logs and screenshots attached !
pls what could be the problem? has the emmc damaged or i need to reprogram emmc or change? pls share your suggestions!

"
[ Open \\ISP Pinout picture ]
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-3879
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-3879
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-3879
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-3879
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... CLK, CMD, DAT0 not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Failed to initialize eMMC (return code: 226, Over current detected) !!!

SERVICE & AUX SD-MMC Pinouts:"

this above i get if i reconnect again with isp pinouts! i check the pinouts are ok!
looking for your help!
wbr

 

[farhanab]

c7000 u3 frp remove eft old veroin 2.1 fail to remove



Opening Port COM22...........OK

Verifying Download Mod

OK

Initialization.......OK

Reading Phone Partitation Table........OK

Partition Size : 8192

Unpak pit .......OK

FLASHING FIRMWARE TO PHONE.....

Sending data: ..........OK

FLASHING DONE!

Rebooting PDA TO NORMAL MODE........OK

Waiting For ADB Device.....Detecting Device Info.....DONE

Device Model: SM-C7000

Device CPU: arm64-v8a

Android SDK: 24

Android Version: 7.0

Resetting FRP.......OK