| Feature | Description |
|---|
| AF-ADB-Cmd | |
| AF FullSweep Enable | Enable full lens sweep for autofocus |
| AF FullSweep Disable | Disable full lens sweep for autofocus |
| AF ADB Command | Execute ADB commands for autofocus |
| Open AF Log | Open autofocus log |
| AF Logcat | View autofocus logcat |
| Show Water Mark | Display watermark in logs |
| Select Pull Path | Select the path for pulling logs and images |
| Pull Logs | Pull logs from the device |
| Clear Cam Logs | Clear camera logs on the device |
| Pull Images | Pull images from the device |
| Clear Cam Images | Clear camera images on the device |
| Pull Raws | Pull raw images from the device |
| Clear Cam Raws | Clear camera raw images on the device |
| AF-PreCheck | |
| AF Precheck | Perform autofocus precheck |
| Driver Check | Check the camera driver status |
| AF OTP DUMP Enable | Enable dumping autofocus OTP |
| AF OTP INFO PULL | Pull information from autofocus OTP |
| AF OTP DUMP Disable | Disable dumping autofocus OTP |
| PD Driver Check Enable | Enable phase detection driver check |
| Actuator Performance Check | Check actuator performance |
| Actuator Hysteresis Check | Check actuator hysteresis |
| Select Log File | Select the file for logging |
| Select Log's Folder | Select a folder for logs |
| PD Driver Check | Check phase detection driver status |
| OTP Infinity | Check OTP infinity status |
| ldxO, ldx9, ldxl, ldx4 | Check specific OTP values |
| Golden Module Check | Check for the golden module status |
| PD Calibration Check Enable | Enable phase detection calibration check |
| OTP Macro: ldx2, ldx5 | Check specific OTP macro values |
| AF Log Extract | Extract logs for autofocus analysis |
| Manual AF (move lens0dx) | Manually move the autofocus lens |
| Disable Manual AF | Disable manual autofocus |
| PD Calibration Check | Check phase detection calibration status |
| AF-Basic-Calibration | |
| Enable Fullsweep | Enable full lens sweep for calibration |
| Disable FullSweep | Disable full lens sweep for calibration |
| AF Basic Tuning | Perform basic autofocus tuning |
| 1 set AF Table | Set autofocus table |
| AF Log Extract | Extract logs for calibration analysis |
| Table Configure Keywords | Configure keywords for the table |
| 2. AF SAG Compensation | Perform SAG compensation for autofocus |
| 3. Draw FV Curve | Draw focus value curve for calibration |
| Draw FV | Draw focus value for calibration |
| AF-LOG-Analysis | |
| Select AF Log File | Select the file for AF log analysis |
| Select AF Log Folder | Select a folder for AF logs |
| Setting focus mode to | Set focus mode during analysis |
| af_pdaf_proc_pd_single | Perform phase detection single focus during analysis |
| needed_rev_scan_at_fail | Set needed reverse scan at failure during analysis |
| going to the final position | Move to the final position during analysis |
| AF Basic Log Analysis | Perform basic log analysis for autofocus |
| af_process | Analyze autofocus process logs |
| finescan | Analyze finescan logs |
| af_haf_fine_search | Analyze haf fine search logs |
| is_trig_refocus | Analyze trigger refocus logs |
| Converge done | Analyze convergence status logs |
| ALGO Complete | Analyze algorithm completion logs |
| af_generate_sad | Analyze SAD generation logs |
| Open With TextanaIysisTooI | Open logs with the TextanaIysisTooI tool |
| Open With Notepad* * | Open logs with Notepad |
| curve_fitting | Analyze curve fitting logs |
| change ratio | Analyze change ratio logs |
| af_caf_search | Analyze continuous autofocus search logs |
| flat | Analyze flatness logs |
| spotlight | Analyze spotlight logs |
| min_max | Analyze min_max logs |
| PublishPDLibOutput pdlib | Publish PD library output logs |
