Please Tell Me Product Supporter Of EME Mobile Tool (EMT), Can I Remove Redmi S2&Y2 Screen Lock Without Loss Any DATA In EME Mobile Tool (EMT) If Yes What Will Process Tell Me
& Sorry Sir But Here I Showing Other Tool LOG Here Software Tool Showing Disable Screen Lock Successfully But Still Lock Mobile
Device : Xiaomi Redmi S2
Operation : Disable Locks
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM443)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1600400 [8953] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8953]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8953, eMMC, 32 GB
LU Count : 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Redmi S2
Software : PKQ1.181203.001, V11.0.5.0.PEFMIXM [Fri Mar 6 11:35:24 WIB 2020]
Android Ver. : 9
Patch Level : 2020-03-01
USERDATA : Encrypted
Disabling Android Locks...Done
Operation Finished.
QcFire Ver. 4.2
Thanks & Regards By:All TECH 4 You
& Sorry Sir But Here I Showing Other Tool LOG Here Software Tool Showing Disable Screen Lock Successfully But Still Lock Mobile
Device : Xiaomi Redmi S2
Operation : Disable Locks
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM443)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1600400 [8953] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8953]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8953, eMMC, 32 GB
LU Count : 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Redmi S2
Software : PKQ1.181203.001, V11.0.5.0.PEFMIXM [Fri Mar 6 11:35:24 WIB 2020]
Android Ver. : 9
Patch Level : 2020-03-01
USERDATA : Encrypted
Disabling Android Locks...Done
Operation Finished.
QcFire Ver. 4.2
Thanks & Regards By:All TECH 4 You
