Frequently Asked Question

Status
Not open for further replies.

Jamil Mobile

Marhaba Team
Oct 26, 2016
509
1,603
Pakistan
Skype
jamilmobile
Sonork ID
100.1623251
Frequently Asked Question






Q: ERROR[000]: Unable to halt core.
Q: ERROR[001]: Server is busy.
Q: ERROR[002]: Server failed to start. Buffer address not set.
Q: ERROR[003]: Server failed to start. Started flag not set.
Q: ERROR[004]: Server did not reply to HELLO command.
Q: ERROR[005]: Server does not respond to commands. Status cannot be read.
Q: ERROR[006]: Page operation failed. Page %d.
Q: ERROR[007]: Unable to init flash device because it is out of order. Server initialization failed.
Q: ERROR[008]: Unknown flash device. Device No:ID = %d:%x.
Q: ERROR[009]: Cannot connect. No target device or JTAG speed is too high.
Q: ERROR[010]: Unsupported device core. Core ID = %x.
Q: ERROR[011]: Cannot find Medusa JTAG device. Please connect Medusa JTAG to your computer.
Q: ERROR[012]: Current server does not support reading with ECC.
Q: ERROR[013]: Current server does not support writing with ECC.
Q: ERROR[014]: Current server does not support bad blocks marking.
Q: ERROR[015]: Block operation failed. Block %d.
Q: ERROR[016]: Selected device core ID mismatch. Core ID = %x.
Q. ERROR[017]: No flash devices detected.
Q: ERROR[018]: Logical block operation failed.
Q: ERROR[019]: Cannot open file "%s" for reading.
Q: ERROR[020]: Invalid or damaged firmware file "%s". BOOT section cannot be found.
Q: ERROR[021]: Invalid or damaged firmware file "%s". Can't find FIRMWARE section.
Q: ERROR[022]: JTAG connection error. Please check target device connection and power supply.
Q: ERROR[023]: Device is busy.
Q: ERROR[024]: This device does not support emergency repair mode. You have to use full firmware operations.
Q: ERROR[025]: Read error or unexpected end of input file.
Q: ERROR[026]: Write to flash device must be block aligned (block size %k).
Q: ERROR[027]: VREF = %d.%dV is less than required level. Please check target device power supply.
Q: ERROR[028]: Target device has been disconnected ...
Q: ERROR[029]: Invalid or damaged firmware file. Cannot find required section.

Q: ERROR[000]: Unable to halt core.


A: Verify JTAG connection.
Q: ERROR[001]: Server is busy.


A: Connection error. Verify JTAG connection.
Q: ERROR[002]: Server failed to start. Buffer address not set.


A:
a. Connection error. Verify JTAG connection.
b. Unsupported core type.
Q: ERROR[003]: Server failed to start. Started flag not set.


A:
a. Connection error. Verify JTAG connection.
b. Unsupported core type.
Q: ERROR[004]: Server did not reply to HELLO command.


A:
a. Connection error. Verify JTAG connection.
b. Unsupported core type.
Q: ERROR[005]: Server does not respond to commands. Status cannot be read.


A:
a. Connection error. Verify JTAG connection.
b. Core operates incorrectly or version is not supported. Repair is impossible.
Q: ERROR[006]: Page operation failed. Page %d.


A: Flash device page damaged. Repair is impossible.
Q: ERROR[007]: Unable to init flash device because it is out of order. Server initialization failed.


A: Flash device initialization error. Repair is impossible.
Q: ERROR[008]: Unknown flash device. Device No:ID = %d:%x.


A: Unknown flash device. Set device parameters manually.
Q: ERROR[009]: Cannot connect. No target device or JTAG speed is too high.


A: No target device. Verify JTAG connection. Reduce connection speed.
Q: ERROR[010]: Unsupported device core. Core ID = %x.


A: Unsupported CPU core.
Q: ERROR[011]: Cannot find Medusa JTAG device. Please connect Medusa JTAG to your computer.


A: Medusa JTAG is not connected. Connect adaptor to computer via USB.
Q: ERROR[012]: Current server does not support reading with ECC.


A:
a. Should not occur. Kept in terms of compatibility.
b. Internal error. Contact the developers (provide “Medusa.log” log file).
Q: ERROR[013]: Current server does not support writing with ECC.


A:
a. Should not occur. Kept in terms of compatibility.
b. Internal error. Contact the developers (provide “Medusa.log” log file).
Q: ERROR[014]: Current server does not support bad blocks marking.


A:
a. Should not occur. Kept in terms of compatibility.
b. Internal error. Contact the developers (provide “Medusa.log” log file).
Q: ERROR[015]: Block operation failed. Block %d.


A: Flash memory block in use is damaged. Repair is impossible.
Q: ERROR[016]: Selected device core ID mismatch. Core ID = %x.


A:
a. Cores ID mismatch. Verify device model selection.
b. Contact the developers (provide “Medusa.log” log file).
Q. ERROR[017]: No flash devices detected.


A:
a. Known flash devices not detected.
b. Damaged flash device. Repair is impossible.
Q: ERROR[018]: Logical block operation failed.


A: Flash device logical block in use is damaged. Repair is impossible.
Q: ERROR[019]: Cannot open file "%s" for reading.


A:
a. File access denied – verify access rights.
b. Close other applications using this file.
Q: ERROR[020]: Invalid or damaged firmware file "%s". BOOT section cannot be found.


A: Download new firmware file from the support area.
Q: ERROR[021]: Invalid or damaged firmware file "%s". Can't find FIRMWARE section.


A: Download new firmware file from the support area.
Q: ERROR[022]: JTAG connection error. Please check target device connection and power supply.


A: Verify JTAG connection. Reduce connection speed.
Q: ERROR[023]: Device is busy.


A:
a. Verify JTAG connection. Reduce connection speed.
b. Flash device may be damaged.
Q: ERROR[024]: This device does not support emergency repair mode. You have to use full firmware operations.


A:
a. Should not occur. Kept in terms of compatibility.
b. Internal error. Contact the developers (provide “Medusa.log” log file).
Q: ERROR[025]: Read error or unexpected end of input file.


A:
a. File access denied – verify access rights.
b. Close other applications using this file.
c. Download new firmware file from the support area.
Q: ERROR[026]: Write to flash device must be block aligned (block size %k).


A: Write borders (beginning and length) should be a multiple of the block size.
Q: ERROR[027]: VREF = %d.%dV is less than required level. Please check target device power supply.


A:
a. Verify JTAG connection.
b. Check whether target device is connected and power supply.
Q: ERROR[028]: Target device has been disconnected ...


A:
a. Device is disconnected or connection has been disrupted.
b. Verify JTAG connection.
c. Check whether target device is connected and power supply.
Q: ERROR[029]: Invalid or damaged firmware file. Cannot find required section.


A: Download new firmware file from the support area.
 
  • Like
Reactions: Admin
Status
Not open for further replies.
Top