Selected model: OPPO CPH1923 (OPPO A1K)
Operation: Erase FRP And Wipe
Software version: 9.7
Erasing of partitions can damage your device.
Make sure that you have a backup created. Continue? YES
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM110 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Install LibUSB... OK
Waiting for device... OK
Open port... OK
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM110 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xD0DF3096, 0x11496610, 0x328923BF, 0x0B6F620C
Get Chip ID... [MT6765]
Get SOC ID... [9A87072444E37678F91832C953F23E9F31F070CC00FC7720F51ABE046A996603]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x150100514436334D420356C4ACD81667
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: QD63MB
EMMC_ID : 0x150100514436334D420356C4ACD81667
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0080000000 (2.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: Exceeded its maximum estimated device life time
DeviceLifeTimeEstB: Exceeded its maximum estimated device life time
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : OPPO
Product Manufacturer : OPPO
Product Model : OPPO A1k
Product Name : CPH1923
Product Device : OP486C
Product Board : oppo6762_18540
Board Platform : mt6765
Build ID : PPR1.180610.011
Build Date : Thu Dec 12 11:53:05 CST 2024
Display ID : CPH1923EX_11_A.43
Security Patch : 2021-05-05
Version SDK : 28
Version Release : 9
Version Codename : REL
Firmware Version : 1733975830
Userdata FS Type : EXT4
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/OPPO_CPH1923%20(OPPO%20A1K)/FRP_BACKUP_(2025-10-4_15-5-16)/
Format FRP... [P1] OK
Writting FRP data... OK
Formatting "userdata" partition... [P1] OK
Formatting "cache" partition... [P1] OK
Formatting "metadata" partition... [P1] OK
Creating default filesystems... [USERDATA: EXT4] ... [CACHE: EXT4] ... OK
Wipe data done!
Operation: Erase FRP And Wipe
Software version: 9.7
Erasing of partitions can damage your device.
Make sure that you have a backup created. Continue? YES
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM110 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Install LibUSB... OK
Waiting for device... OK
Open port... OK
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM110 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xD0DF3096, 0x11496610, 0x328923BF, 0x0B6F620C
Get Chip ID... [MT6765]
Get SOC ID... [9A87072444E37678F91832C953F23E9F31F070CC00FC7720F51ABE046A996603]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x150100514436334D420356C4ACD81667
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: QD63MB
EMMC_ID : 0x150100514436334D420356C4ACD81667
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0080000000 (2.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: Exceeded its maximum estimated device life time
DeviceLifeTimeEstB: Exceeded its maximum estimated device life time
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : OPPO
Product Manufacturer : OPPO
Product Model : OPPO A1k
Product Name : CPH1923
Product Device : OP486C
Product Board : oppo6762_18540
Board Platform : mt6765
Build ID : PPR1.180610.011
Build Date : Thu Dec 12 11:53:05 CST 2024
Display ID : CPH1923EX_11_A.43
Security Patch : 2021-05-05
Version SDK : 28
Version Release : 9
Version Codename : REL
Firmware Version : 1733975830
Userdata FS Type : EXT4
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/OPPO_CPH1923%20(OPPO%20A1K)/FRP_BACKUP_(2025-10-4_15-5-16)/
Format FRP... [P1] OK
Writting FRP data... OK
Formatting "userdata" partition... [P1] OK
Formatting "cache" partition... [P1] OK
Formatting "metadata" partition... [P1] OK
Creating default filesystems... [USERDATA: EXT4] ... [CACHE: EXT4] ... OK
Wipe data done!
