Oppo f5 cph1723 emmc write problem get this notification while i want to write emmc dump file
WARNING: The eMMC CID does not seem to be supported for this boot file !!!
Are you sure you want to continue?
and this is log
Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8842-5436
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: HBG4a2 (0x484247346132), rev: 0xA5, serial number: 0x1C7BD403
Manufacturing date: Oct 2017
CID: 90014A48 42473461 32A51C7B D403A408
CSD: D0270132 8F5903FF FFFFFFE7 8A400016
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 29.12 GiB(31,268,536,320 bytes)
Boot write skipped.
Current partition access:
Access to boot partition 2
Loading file: "\\E:\China%20Mobile\Oppo\F5\dump%20f5%20langsung%20on%20cph%201723\OPPO_CPH1723(CPH1723EX_11_A.39_190924-7.1.1-N6F26Q)[H9TQ26ACLTMCUR_47BBC655]\boot2.bin", size: 4 MiB...
Writing boot2 (8192 sectors)... Done in 8.930 s
Current partition access:
Access to user area
Loading file: "\\E:\China%20Mobile\Oppo\F5\dump%20f5%20langsung%20on%20cph%201723\OPPO_CPH1723(CPH1723EX_11_A.39_190924-7.1.1-N6F26Q)[H9TQ26ACLTMCUR_47BBC655]\userarea_1GiB.bin", size: 1 GiB...
Writing userarea (2097152 sectors)... Failed to write block 0x00D60000:65536 (return code: 1, CMD Error: Timeout)
cmd response: 0x900, card status: 0x0, card state: 4 (Card is in transfer state)
status: unknown (0)
[32]Failed to Switch (return code: 1, CMD Error: Timeout) !!!
WARNING: The eMMC CID does not seem to be supported for this boot file !!!
Are you sure you want to continue?
and this is log
Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8842-5436
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: HBG4a2 (0x484247346132), rev: 0xA5, serial number: 0x1C7BD403
Manufacturing date: Oct 2017
CID: 90014A48 42473461 32A51C7B D403A408
CSD: D0270132 8F5903FF FFFFFFE7 8A400016
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 29.12 GiB(31,268,536,320 bytes)
Boot write skipped.
Current partition access:
Access to boot partition 2
Loading file: "\\E:\China%20Mobile\Oppo\F5\dump%20f5%20langsung%20on%20cph%201723\OPPO_CPH1723(CPH1723EX_11_A.39_190924-7.1.1-N6F26Q)[H9TQ26ACLTMCUR_47BBC655]\boot2.bin", size: 4 MiB...
Writing boot2 (8192 sectors)... Done in 8.930 s
Current partition access:
Access to user area
Loading file: "\\E:\China%20Mobile\Oppo\F5\dump%20f5%20langsung%20on%20cph%201723\OPPO_CPH1723(CPH1723EX_11_A.39_190924-7.1.1-N6F26Q)[H9TQ26ACLTMCUR_47BBC655]\userarea_1GiB.bin", size: 1 GiB...
Writing userarea (2097152 sectors)... Failed to write block 0x00D60000:65536 (return code: 1, CMD Error: Timeout)
cmd response: 0x900, card status: 0x0, card state: 4 (Card is in transfer state)
status: unknown (0)
[32]Failed to Switch (return code: 1, CMD Error: Timeout) !!!
