- Sep 25, 2018
- 32
- 4
- Skype
- waseemshahzad1186
Redme Note 8 Pro 4g fixed
1. flash eng
Selected model: Xiaomi Redmi Note 8 Pro (Begonia)
Operation: Flash (Download only)
Software version: 8.9
Parse scatter file... OK
Load Rom Images... OK
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x0984261F, 0xA9CCCAF1, 0xDC918577, 0x0C074AEA
Get Chip ID... [MT6785]
Get SOC ID... [9F69636D511260F96DDE3FD53EC96C35D11F2642FC350B072A5435EDF87B33BF]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM2H7001CM-B518 (0600)
Load EMI config from preloader... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM2H7001CM-B518
UFS_FWVER : 0600
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x0EE5800000 (59.59Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0180000000 (6.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 10% - 20% device life time used
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : Redmi Note 8 Pro
Product Name : begonia
Product Device : begonia
Product Board : begonia
Board Platform : mt6785
Build ID : QP1A.190711.020
Build Date : Fri May 14 01:07:57 WIB 2021
Display ID : QP1A.190711.020
Security Patch : 2021-04-01
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : V12.0.8.0.QGGMIXM
Userdata FS Type : EXT4
MiAcc Find Device : Disabled
Get scatter info... OK
Verify scatter file... OK
Do NAND BMT remark... OK
Setup download info... OK
Get partition table catagory... OK [GPT]
Read mirror partition table... OK
Checking partition table layout changed... OK
Read major partition table... OK
Checking major partition table layout changed... OK
Download "preloader"... OK "preloder_backup"... OK
Download "recovery"... OK
Download "vbmeta"... OK
Download "efuse"... OK
Download "md1img"... OK
Download "spmfw"... OK
Download "audio_dsp"... OK
Download "scp1"... OK
Download "scp2"... OK
Download "sspm_1"... OK
Download "sspm_2"... OK
Download "cam_vpu1"... OK
Download "cam_vpu2"... OK
Download "cam_vpu3"... OK
Download "gz1"... OK
Download "gz2"... OK
Download "lk"... OK
Download "lk2"... OK
Download "boot"... OK
Download "logo"... OK
Download "dtbo"... OK
Download "tee1"... OK
Download "tee2"... OK
Download "vendor"... OK
Download "system"... OK
Download "cache"... OK
Download "gsort"... OK
Download "oem_misc1"... OK
Download "exaid"... OK
Download "cust"... OK
Download "userdata"... OK
Flashing done!
2. goto recovery and wipe reset
3 . flash golble 12.0.8.0
Selected model: Xiaomi Redmi Note 8 Pro (Begonia)
Operation: Flash (Download only)
Software version: 8.9
Parse scatter file... OK
Load Rom Images... OK
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x0984261F, 0xA9CCCAF1, 0xDC918577, 0x0C074AEA
Get Chip ID... [MT6785]
Get SOC ID... [9F69636D511260F96DDE3FD53EC96C35D11F2642FC350B072A5435EDF87B33BF]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM2H7001CM-B518 (0600)
Load EMI config from preloader... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM2H7001CM-B518
UFS_FWVER : 0600
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x0EE5800000 (59.59Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0180000000 (6.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 10% - 20% device life time used
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : begonia
Product Name : begonia
Product Device : begonia
Product Board : begonia
Board Platform : mt6785
Build ID : PPR1.180610.011
Build Date : Thu Oct 31 22:02:24 CST 2019
Display ID : begonia-userdebug 9 PPR1.180610.011 FACTORY-BEGONIA-1101 test-keys
Security Patch : 2019-06-05
Version SDK : 28
Version Release : 9
Version Codename : REL
Firmware Version : FACTORY-BEGONIA-1101
Userdata FS Type : EXT4
MiAcc Find Device : Disabled
Get scatter info... OK
Verify scatter file... OK
Do NAND BMT remark... OK
Setup download info... OK
Get partition table catagory... OK [GPT]
Read mirror partition table... OK
Checking partition table layout changed... OK
Read major partition table... OK
Checking major partition table layout changed... OK
Download "preloader"... OK "preloder_backup"... OK
Download "recovery"... OK
Download "vbmeta"... OK
Download "efuse"... OK
Download "md1img"... OK
Download "spmfw"... OK
Download "audio_dsp"... OK
Download "scp1"... OK
Download "scp2"... OK
Download "sspm_1"... OK
Download "sspm_2"... OK
Download "cam_vpu1"... OK
Download "cam_vpu2"... OK
Download "cam_vpu3"... OK
Download "gz1"... OK
Download "gz2"... OK
Download "lk"... OK
Download "lk2"... OK
Download "boot"... OK
Download "logo"... OK
Download "dtbo"... OK
Download "tee1"... OK
Download "tee2"... OK
Download "vendor"... OK
Download "system"... OK
Download "cache"... OK
Download "gsort"... OK
Download "oem_misc1"... OK
Download "exaid"... OK
Download "cust"... OK
Download "userdata"... OK
Flashing done!
after flash imei will be null
4. repaire imei
Selected model: Xiaomi Redmi Note 8 Pro (Begonia)
Operation: Repair
Software version: 8.9
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x0984261F, 0xA9CCCAF1, 0xDC918577, 0x0C074AEA
Get Chip ID... [MT6785]
Get SOC ID... [9F69636D511260F96DDE3FD53EC96C35D11F2642FC350B072A5435EDF87B33BF]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM2H7001CM-B518 (0600)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM2H7001CM-B518
UFS_FWVER : 0600
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x0EE5800000 (59.59Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0180000000 (6.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 10% - 20% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : Redmi Note 8 Pro
Product Name : begonia
Product Device : begonia
Product Board : begonia
Board Platform : mt6785
Build ID : QP1A.190711.020
Build Date : Fri May 14 01:07:57 WIB 2021
Display ID : QP1A.190711.020
Security Patch : 2021-04-01
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : V12.0.8.0.QGGMIXM
Userdata FS Type : EXT4
MiAcc Find Device : Disabled
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Read IMEI... error
Repairing IMEI...
IMEI 1: 86098xxxxxxxxxxx
IMEI 2: 86098xxxxxxxxxxx
Write IMEI and patch CERT [NVDATA]... OK
Load partiton for patching... OK
Checking boot patch possiblity... POSSIBLE WITH BOOT UNLOCK
Patching CERT... OK
Save patched partiton... OK
Selected "Auto unlock bootloader"
Read security partition from phone... OK
Write security partition to phone... OK
Unlock bootloader done!
Write IMEI and patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security and Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.
Done.
1. flash eng
Selected model: Xiaomi Redmi Note 8 Pro (Begonia)
Operation: Flash (Download only)
Software version: 8.9
Parse scatter file... OK
Load Rom Images... OK
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x0984261F, 0xA9CCCAF1, 0xDC918577, 0x0C074AEA
Get Chip ID... [MT6785]
Get SOC ID... [9F69636D511260F96DDE3FD53EC96C35D11F2642FC350B072A5435EDF87B33BF]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM2H7001CM-B518 (0600)
Load EMI config from preloader... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM2H7001CM-B518
UFS_FWVER : 0600
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x0EE5800000 (59.59Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0180000000 (6.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 10% - 20% device life time used
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : Redmi Note 8 Pro
Product Name : begonia
Product Device : begonia
Product Board : begonia
Board Platform : mt6785
Build ID : QP1A.190711.020
Build Date : Fri May 14 01:07:57 WIB 2021
Display ID : QP1A.190711.020
Security Patch : 2021-04-01
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : V12.0.8.0.QGGMIXM
Userdata FS Type : EXT4
MiAcc Find Device : Disabled
Get scatter info... OK
Verify scatter file... OK
Do NAND BMT remark... OK
Setup download info... OK
Get partition table catagory... OK [GPT]
Read mirror partition table... OK
Checking partition table layout changed... OK
Read major partition table... OK
Checking major partition table layout changed... OK
Download "preloader"... OK "preloder_backup"... OK
Download "recovery"... OK
Download "vbmeta"... OK
Download "efuse"... OK
Download "md1img"... OK
Download "spmfw"... OK
Download "audio_dsp"... OK
Download "scp1"... OK
Download "scp2"... OK
Download "sspm_1"... OK
Download "sspm_2"... OK
Download "cam_vpu1"... OK
Download "cam_vpu2"... OK
Download "cam_vpu3"... OK
Download "gz1"... OK
Download "gz2"... OK
Download "lk"... OK
Download "lk2"... OK
Download "boot"... OK
Download "logo"... OK
Download "dtbo"... OK
Download "tee1"... OK
Download "tee2"... OK
Download "vendor"... OK
Download "system"... OK
Download "cache"... OK
Download "gsort"... OK
Download "oem_misc1"... OK
Download "exaid"... OK
Download "cust"... OK
Download "userdata"... OK
Flashing done!
2. goto recovery and wipe reset
3 . flash golble 12.0.8.0
Selected model: Xiaomi Redmi Note 8 Pro (Begonia)
Operation: Flash (Download only)
Software version: 8.9
Parse scatter file... OK
Load Rom Images... OK
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x0984261F, 0xA9CCCAF1, 0xDC918577, 0x0C074AEA
Get Chip ID... [MT6785]
Get SOC ID... [9F69636D511260F96DDE3FD53EC96C35D11F2642FC350B072A5435EDF87B33BF]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM2H7001CM-B518 (0600)
Load EMI config from preloader... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM2H7001CM-B518
UFS_FWVER : 0600
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x0EE5800000 (59.59Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0180000000 (6.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 10% - 20% device life time used
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : begonia
Product Name : begonia
Product Device : begonia
Product Board : begonia
Board Platform : mt6785
Build ID : PPR1.180610.011
Build Date : Thu Oct 31 22:02:24 CST 2019
Display ID : begonia-userdebug 9 PPR1.180610.011 FACTORY-BEGONIA-1101 test-keys
Security Patch : 2019-06-05
Version SDK : 28
Version Release : 9
Version Codename : REL
Firmware Version : FACTORY-BEGONIA-1101
Userdata FS Type : EXT4
MiAcc Find Device : Disabled
Get scatter info... OK
Verify scatter file... OK
Do NAND BMT remark... OK
Setup download info... OK
Get partition table catagory... OK [GPT]
Read mirror partition table... OK
Checking partition table layout changed... OK
Read major partition table... OK
Checking major partition table layout changed... OK
Download "preloader"... OK "preloder_backup"... OK
Download "recovery"... OK
Download "vbmeta"... OK
Download "efuse"... OK
Download "md1img"... OK
Download "spmfw"... OK
Download "audio_dsp"... OK
Download "scp1"... OK
Download "scp2"... OK
Download "sspm_1"... OK
Download "sspm_2"... OK
Download "cam_vpu1"... OK
Download "cam_vpu2"... OK
Download "cam_vpu3"... OK
Download "gz1"... OK
Download "gz2"... OK
Download "lk"... OK
Download "lk2"... OK
Download "boot"... OK
Download "logo"... OK
Download "dtbo"... OK
Download "tee1"... OK
Download "tee2"... OK
Download "vendor"... OK
Download "system"... OK
Download "cache"... OK
Download "gsort"... OK
Download "oem_misc1"... OK
Download "exaid"... OK
Download "cust"... OK
Download "userdata"... OK
Flashing done!
after flash imei will be null
4. repaire imei
Selected model: Xiaomi Redmi Note 8 Pro (Begonia)
Operation: Repair
Software version: 8.9
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM37 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x0984261F, 0xA9CCCAF1, 0xDC918577, 0x0C074AEA
Get Chip ID... [MT6785]
Get SOC ID... [9F69636D511260F96DDE3FD53EC96C35D11F2642FC350B072A5435EDF87B33BF]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM2H7001CM-B518 (0600)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM2H7001CM-B518
UFS_FWVER : 0600
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x0EE5800000 (59.59Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0180000000 (6.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 10% - 20% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : Redmi Note 8 Pro
Product Name : begonia
Product Device : begonia
Product Board : begonia
Board Platform : mt6785
Build ID : QP1A.190711.020
Build Date : Fri May 14 01:07:57 WIB 2021
Display ID : QP1A.190711.020
Security Patch : 2021-04-01
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : V12.0.8.0.QGGMIXM
Userdata FS Type : EXT4
MiAcc Find Device : Disabled
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Read IMEI... error
Repairing IMEI...
IMEI 1: 86098xxxxxxxxxxx
IMEI 2: 86098xxxxxxxxxxx
Write IMEI and patch CERT [NVDATA]... OK
Load partiton for patching... OK
Checking boot patch possiblity... POSSIBLE WITH BOOT UNLOCK
Patching CERT... OK
Save patched partiton... OK
Selected "Auto unlock bootloader"
Read security partition from phone... OK
Write security partition to phone... OK
Unlock bootloader done!
Write IMEI and patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security and Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.
Done.