redmi 5 plus vince , 1st flashing with global rom (phone is chines rom)
then reprogram with ufi isp pinout
but after flash stuck on logo only
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-1107
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 2.8 V
Bus: 8 bit (HS SDR 52MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: GD6BMB (0x474436424d42), rev: 0x01, serial number: 0x65FBCA7C
Manufacturing date: Dec 2017
CID: 15010047 4436424D 420165FB CA7CC4DC
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 29.12 GiB(31,268,536,320 bytes)
Cache size: 64 MiB
Hardware reset function: 1
Partition configuration: 0x38
No boot acknowledge is sent (default)
User area is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
ANDROID System Info:
platform: msm8953, cpu abi: arm64-v8a
manufacturer: Xiaomi
board: msm8953, name: vince
brand: xiaomi, model: Redmi 5 Plus
build model list: Redmi 5 Plus
build id: OPM1.171019.019, version: 8.1.0 Oreo (ZQL1711-vince-build-20180817135416)
build description: vince-user 8.1.0 OPM1.171019.019 V9.6.5.0.OEGMIFD release-keys
crypto state: encrypted?
Custom moviNAND command is not supported for this device(MMC51).
then reprogram with ufi isp pinout
but after flash stuck on logo only
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-1107
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 2.8 V
Bus: 8 bit (HS SDR 52MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: GD6BMB (0x474436424d42), rev: 0x01, serial number: 0x65FBCA7C
Manufacturing date: Dec 2017
CID: 15010047 4436424D 420165FB CA7CC4DC
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 29.12 GiB(31,268,536,320 bytes)
Cache size: 64 MiB
Hardware reset function: 1
Partition configuration: 0x38
No boot acknowledge is sent (default)
User area is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
ANDROID System Info:
platform: msm8953, cpu abi: arm64-v8a
manufacturer: Xiaomi
board: msm8953, name: vince
brand: xiaomi, model: Redmi 5 Plus
build model list: Redmi 5 Plus
build id: OPM1.171019.019, version: 8.1.0 Oreo (ZQL1711-vince-build-20180817135416)
build description: vince-user 8.1.0 OPM1.171019.019 V9.6.5.0.OEGMIFD release-keys
crypto state: encrypted?
Custom moviNAND command is not supported for this device(MMC51).
