IM VERY NEW PLEASE HELP
IS IT HARDWARE PROBLEM???
PROBLEM IS LOGO REBOOTING
Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 12 MHz
CMD Pullup Level: 1812 mV
CMD Active Level: 1864 mV
EMMC Device Information :
EMMC CID: 150100335636434D4202EBFECE8C4753
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: 3V6CMB , HEX: 335636434D42 , S/N: EBFECE8C , rev. 0x02
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 4/2020
EMMC ROM 1 (Main User Data) Capacity: 119276 MB (001D1EC00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 29399 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x02 , width 8bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: 3V6CMB_EBFECE8C_20221017_102731.extcsd
EMMC Init completed.
Get firmware version
Error: Mount [data] failed PartType: LINUX
Error: Except: Unmount [data/] failed
Firmware info not found
IS IT HARDWARE PROBLEM???
PROBLEM IS LOGO REBOOTING
Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 12 MHz
CMD Pullup Level: 1812 mV
CMD Active Level: 1864 mV
EMMC Device Information :
EMMC CID: 150100335636434D4202EBFECE8C4753
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: 3V6CMB , HEX: 335636434D42 , S/N: EBFECE8C , rev. 0x02
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 4/2020
EMMC ROM 1 (Main User Data) Capacity: 119276 MB (001D1EC00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 29399 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x02 , width 8bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: 3V6CMB_EBFECE8C_20221017_102731.extcsd
EMMC Init completed.
Get firmware version
Error: Mount [data] failed PartType: LINUX
Error: Except: Unmount [data/] failed
Firmware info not found