Legitunlocks.com
Tool Organizers

(return code: 1, CMD Error: Timeout) cmd response: 0x900, card status: 0x0, card state: 4 (Card is in transfer state)

L

ligteltelecom

Junior Member
Jan 31, 2020
4
0
Hi Guys

How solve this problem with UFI ?
i have this problem all boards.
Code: 
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-8115
 Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 48MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
 Card/BGA: BGA (Discrete embedded) - High density MMC
 Manufacturer ID: 0x90 (SK Hynix)
 Product name: hC8aP (0x68433861503e), rev: 0x03, serial number: 0x60530A5E
 Manufacturing date: mar 2019
CID: 90014A68 43386150 3E036053 0A5E36B6
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
EXT_CSD revision: 1.8 (MMC v5.1) 
Partition info:
 Boot1: 4096 KiB
 Boot2: 4096 KiB
 RPMB: 16384 KiB
 User area: 58.24 GiB(62,537,072,640 bytes)

 Writing preloader header... Done
Current partition access: 
 Access to boot partition 1
 Writing preloader at 0x00000000 (459 sectors)... Done in 0.093 s
Setting boot partition config to 0x48... Done
Current partition access: 
 Access to user area
Processing file: "recovery.img"... 
 Writing recovery at 0x00108000 (65536 sectors)... Done in 12.538 s
Processing file: "efuse.img"... 
 Writing efuse at 0x10500000 (1 sectors)... Done in 0.001 s
Processing file: "md1img.img"... 
 Writing md1img at 0x10580000 (107595 sectors)... Done in 20.557 s
Processing file: "spmfw.img"... 
 Writing spmfw at 0x16980000 (55 sectors)... Done in 0.012 s
Processing file: "scp.img"... 
 Writing scp1 at 0x16A80000 (1092 sectors)... Done in 0.237 s
Processing file: "scp.img"... 
 Writing scp2 at 0x16B80000 (1092 sectors)... Done in 0.208 s
Processing file: "sspm.img"... 
 Writing sspm_1 at 0x16C80000 (766 sectors)... Done in 0.145 s
Processing file: "sspm.img"... 
 Writing sspm_2 at 0x16D80000 (766 sectors)... Done in 0.145 s
Processing file: "lk.img"... 
 Writing lk at 0x1CE80000 (1588 sectors)... Done in 0.303 s
Processing file: "lk.img"... 
 Writing lk2 at 0x1CF80000 (1588 sectors)... Done in 0.305 s
Processing file: "boot.img"... 
 Writing boot at 0x1D080000 (65536 sectors)... Failed to write block 0x1E300000:65536 (return code: 1, CMD Error: Timeout)
cmd response: 0x900, card status: 0x0, card state: 4 (Card is in transfer state)
status: unknown (0)
 
narayan pathak

narayan pathak

Active Member
Dec 5, 2016
24
4
nepal
ailed to write block 0x00CB0000:65536 (return code: 1, CMD Error: Timeout)
cmd response: 0x900, card status: 0x0, card state: 4 (Card is in transfer state)
status: unknown (0)
[32]Failed to Switch (return code: 1, CMD Error: Timeout) !!!
 
pravin s

pravin s

Junior Member
Aug 24, 2019
1
0
Failed to initialize eMMC (return code: 6, CMD Error: Invalid Voltage Range) !!
 
W

Wankred2

Active Member
May 20, 2020
21
3
Nairobi
Failed to switch[110][0,110,75] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[126][0,126,0] (return code: 4, CMD Error: Invalid response) !!!
 
S

Saiful_Telecom

Junior Member
Feb 1, 2023
3
0
jessore kessabpur
Failed to switch[110][0,110,27] (return code: 1, CMD Error: Timeout) !!! Failed to switch[111][0,111,74] (return code: 4, CMD Error: Invalid response) !!! Failed to switch[112][0,112,3] (return code: 1, CMD Error: Timeout) !!! Failed to switch[171][0,171,0] (return code: 4, CMD Error: Invalid response) !!!
 
a839760072

a839760072

Active Member
Jul 19, 2023
25
1
China
ligteltelecom said:
Hi Guys

How solve this problem with UFI ?
i have this problem all boards.
Code: 
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-8115
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 48MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: hC8aP (0x68433861503e), rev: 0x03, serial number: 0x60530A5E
Manufacturing date: mar 2019
CID: 90014A68 43386150 3E036053 0A5E36B6
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 16384 KiB
User area: 58.24 GiB(62,537,072,640 bytes)

Writing preloader header... Done
Current partition access:
Access to boot partition 1
Writing preloader at 0x00000000 (459 sectors)... Done in 0.093 s
Setting boot partition config to 0x48... Done
Current partition access:
Access to user area
Processing file: "recovery.img"...
Writing recovery at 0x00108000 (65536 sectors)... Done in 12.538 s
Processing file: "efuse.img"...
Writing efuse at 0x10500000 (1 sectors)... Done in 0.001 s
Processing file: "md1img.img"...
Writing md1img at 0x10580000 (107595 sectors)... Done in 20.557 s
Processing file: "spmfw.img"...
Writing spmfw at 0x16980000 (55 sectors)... Done in 0.012 s
Processing file: "scp.img"...
Writing scp1 at 0x16A80000 (1092 sectors)... Done in 0.237 s
Processing file: "scp.img"...
Writing scp2 at 0x16B80000 (1092 sectors)... Done in 0.208 s
Processing file: "sspm.img"...
Writing sspm_1 at 0x16C80000 (766 sectors)... Done in 0.145 s
Processing file: "sspm.img"...
Writing sspm_2 at 0x16D80000 (766 sectors)... Done in 0.145 s
Processing file: "lk.img"...
Writing lk at 0x1CE80000 (1588 sectors)... Done in 0.303 s
Processing file: "lk.img"...
Writing lk2 at 0x1CF80000 (1588 sectors)... Done in 0.305 s
Processing file: "boot.img"...
Writing boot at 0x1D080000 (65536 sectors)... Failed to write block :65536 (return code: 1, CMD Error: Timeout)
cmd response: 0x900, card status: 0x0, card state: 4 (Card is in transfer state)
status: unknown (0)
Click to expand...

My UFI device is also，
i have this problem all boards，
How to fix it
 
a839760072

a839760072

Active Member
Jul 19, 2023
25
1
China
TriddicK said:
У меня с моими адаптерами с программой все хорошо...
Use english, or use translator...
Click to expand...
Okay, I look forward to the official repair. By the way, I am a Chinese user and I hope the official can update the Chinese translation function
 
  • Like
Reactions: TriddicK
P

Playl

Junior Member
Jul 11, 2022
2
0
uk
Is there a fix for this my programmer is 15months old, ive programmed 3 ics successfully and now im getting the same error, this machine hasnt paid for itself yet
 
  • Wow
Reactions: clan123
You must log in or register to reply here.
Top