World First JNY-LX2 Com1.0 Close Fix ID Lock Remove Octoplus Box

Yeminoo

Friend's Martview
Sep 13, 2019
664
519
Myawaddy

JNY-LX2 Com1.0 Close Fix ID Lock Remove Octoplus Box



Before JNY-LX2 ID Lock Remove, Make Sure The Following Steps Are Performed:


Download Huawei Com1.0 Driver
LINK - DOWNLOAD

All Huawei Test Point
LINK - VIEW

Login Username and Pass On Octoplus Huawei Tool


Huawei Com1.0 Close Error Fix


Welcome to Octoplus Huawei Software v.‪1.2.7‬


To enable 'Manufacture' mode dial


  • for Qualcomm and Hisilicon based models: ##2846579##
    ProjectMenu > Background Settings > USB Port Settings > Manufacture Mode
  • for MTK based models: ##14789632##
    ProjectMenu > Background Settings > USB Port Settings > Debug Mode

To enable 'Fastboot' mode


  1. Power off the phone. Remove SD and SIM cards
  2. Press 'Vol-' and insert USB cable
  3. Wait until phone enters 'Fastboot' mode

To enable 'Upgrade' mode


  1. Power off the phone. Remove SD and SIM cards
  2. Press and hold 'Vol-' and 'Vol+' keys and insert USB cable
  3. Wait until phone enters 'Upgrade mode'

Found COM ports:
1: COM7 USB Serial Port
2: COM29 Standard Serial over Bluetooth link
3: COM52 HUAWEI USB COM 1.0
4: COM28 Standard Serial over Bluetooth link


Job ID: 0000000001E2CB55
2021-11-28 12:50:28 GMT -------------------------------------------------
Starting Reset Huawei ID
Selected phone model: ‪JNY-LX2‬
Searching HUAWEI USB COM 1.0 port…
Detected ‪HUAWEI USB COM 1.0‬ port
Writing bootloader KIRIN810_V1…
Initializing remote service connection…
Writing ‪XLOADER‬ partition…
Writing ‪UCE‬ partition…
Writing ‪FASTBOOT‬ partition…
Bootloader Update successfully
Rebooting to fastboot mode…
Searching Fastboot devices…
Found android device: UT7ULK203T005535
Detected ‪Android Sooner Single ADB Interface‬ port


Device Model: ‪JNY-LX2‬
System: ‪JNY-L22 10.1.0.363(C636E1R2P1)‬
Android Version: ‪10‬
Base Version: ‪JNY-LGRP2-OVS 10.1.0.363‬
Custom Version: ‪JNY-L22-CUST 10.1.0.1(C636)‬
Preload Version: ‪JNY-L22-PRELOAD 10.0.1.1(C636R2)‬
C_Version: ‪C636‬
D_Version: ‪D000‬
FB Lock State: ‪LOCKED‬
User Lock State: ‪LOCKED‬
Connecting to the credit server…
Username: cxYQKOIZma
Checking balance…
Your balance: 150 credits
Sending device information…
Sending firmware information…
To perform this operation you need to have: 0 credits.
Removing firmware protection…
Connecting to server…
Waiting for a response from the server…
FB Lock State: ‪UNLOCKED‬
User Lock State: ‪LOCKED‬


Device Model: ‪JNY-LX2‬
System: ‪JNY-L22 10.1.0.363(C636E1R2P1)‬
Resetting Huawei ID…
Formatting secure data…
Rebooting device…


Reset Huawei ID done.
Performed by ‪1.2.7‬ Software version.


If Can't Change Com1.0 To Fastboot [Disconnect USB / Connect Again ]


Download Octoplus Huawei Tool Lasted
LINK - DOWNLOAD

Download JNY-LX2 JNY-L22 _EMUI10.0.1 Firmware
LINK - DOWNLOAD
 

Yuranc8

Friend's Martview
Aug 11, 2021
179
92
Quelimane
Hello I have been trying using a 10k Ohm resistor but it always gives a Error writing to serial port, I've tried changing cables and nothing!
 
Top