Failed to read EXT_CSD !!! problem

Jan 4, 2020
6
0
Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-6132
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 1 bit (SDR 52MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: HCG8a4 (0x484347386134), rev: 0xA2, serial number: 0x4C9B9C26
Manufacturing date: Aug 2018
CID: 90014A48 43473861 34A24C9B 9C2685D2
CSD: D0270132 8F5903FF FFFFFFEF 8A400026
Failed to read EXT_CSD !!!
help me ,,,,,,,,,,,,,,,,,,,,
 

Shaksajib

Junior Member
Nov 28, 2019
1
0
Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-6294
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: QD63MB (0x514436334d42), rev: 0x03, serial number: 0x77C50672
Manufacturing date: Oct 2019
CID: 15010051 4436334D 420377C5 0672A6C8
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
Failed to read EXT_CSD !!!

Failed to read EXT_CSD !!! Poblem FIX
See This Video. I Hope Fix Your Poblem All The Best
 

Pebeyal

Member
Apr 24, 2020
8
1
Chennai
Oppo F11 Pro After connect Ufi Box Only Click Identify eMMC THen SHow this Error

Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-0526
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: hC8aP (0x68433861503e), rev: 0x03, serial number: 0xCB553087
Manufacturing date: Nov 2018
CID: 90014A68 43386150 3E03CB55 3087B598
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
Failed to read EXT_CSD !!!

REconnect some time but handset cannot connect

THen Remove ISP Pinout HandSet Is dead

I Try to Service Center But Service centre firmware Cannot flash show only mtk Port

I need CLK Registrance Image My PLz Help
 

SHOEB AHMED

Active Member
Sep 28, 2019
66
16
player / GSM \ Field
Oppo F11 Pro After connect Ufi Box Only Click Identify eMMC THen SHow this Error

Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-0526
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: hC8aP (0x68433861503e), rev: 0x03, serial number: 0xCB553087
Manufacturing date: Nov 2018
CID: 90014A68 43386150 3E03CB55 3087B598
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
Failed to read EXT_CSD !!!

REconnect some time but handset cannot connect

THen Remove ISP Pinout HandSet Is dead

I Try to Service Center But Service centre firmware Cannot flash show only mtk Port

I need CLK Registrance Image My PLz Help


check this line CMD short or lost 16823
 

Rjswr

Member
Feb 29, 2020
13
0
Zagreb
crypto state: encrypted?
crypto state: encrypted?
Custom moviNAND command is not supported for this device(MMC51).

Setting interface to EasyJtag2/E-Socket
Setting bus width to 8 Bit
Setting frequence to 21 MHz
EMMC Device Information :
EMMC CID: 150100525036344D4201229568DE27F7
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: RP64MB , HEX: 525036344D42 , S/N: 229568DE , rev. 0x01
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 2/2020
EMMC ROM 1 (Main User Data) Capacity: 59640 MB (000E8F800000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 66 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x02 , width 8bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: RP64MB_229568DE_20201118_170342.extcsd
EMMC Init completed.

Operation: Writing eMMC...

Writing to: ROM2 , start: 0x000000000000 , size: 0x000000400000
Input file: C:\Users\raju\Desktop\v11 dump\EMMC_RP64MB_ROM2_000000000000_000000400000.bin
eMMC switching to ROM2
Writing partition...
Error writing at address: 000000000000 , error: -7, DATA SND Timeout Error ... Retry #1
Error writing at address: 000000000000 , error: -7, DATA SND Timeout Error ... Retry #2
Error writing at address: 000000000000 , error: -7, DATA SND Timeout Error ... Retry #3
Too many errors. Writing has been stopped

Setting interface to EasyJtag2/E-Socket
Setting bus width to 8 Bit
Setting frequence to 21 MHz
Can't init device. Reason: DATA RCV CRC Error

Poll_Start failed

Can't init device. Reason: DATA RCV CRC Error

Poll_Start failed

Canceled

Setting interface to EasyJtag2/E-Socket
Setting bus width to 8 Bit
Setting frequence to 21 MHz
Can't init device. Reason: DATA RCV CRC Error

Poll_Start failed

EMMC Device Information :
EMMC CID: 150100525036344D4201229568DE27F7
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: RP64MB , HEX: 525036344D42 , S/N: 229568DE , rev. 0x01
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 2/2020
EMMC ROM 1 (Main User Data) Capacity: 59640 MB (000E8F800000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 66 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x02 , width 8bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: RP64MB_229568DE_20201118_183146.extcsd
EMMC Init completed.

Scanning soft partitions
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #1
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #4
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #5
Too many errors. Reading has been stopped

Setting interface to EasyJtag2/E-Socket
Setting bus width to 8 Bit
Setting frequence to 21 MHz
EMMC Device Information :
EMMC CID: 150100525036344D4201229568DE27F7
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: RP64MB , HEX: 525036344D42 , S/N: 229568DE , rev. 0x01
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 2/2020
EMMC ROM 1 (Main User Data) Capacity: 59640 MB (000E8F800000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 66 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x02 , width 8bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: RP64MB_229568DE_20201118_183220.extcsd
EMMC Init completed.

Operation: Universal Factory Format
Please, wait ...
Error: 21 Verification error

Do you have any solution for this? Thanks in advance.
 

phone.lab

Active Member
Jan 20, 2021
38
6
india
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: HCG8a4 (0x484347386134), rev: 0xA2, serial number: 0x466B002A
Manufacturing date: Jun 2018
CID: 90014A48 43473861 34A2466B 002A6510
CSD: D0270132 8F5903FF FFFFFFEF 8A400026
Failed to read EXT_CSD !!!
 

alim3899

Junior Member
May 20, 2021
3
0
india
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 1MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: Card (removable) - MMC
Manufacturer ID: 0x65 (Unknown)
Product name: M MOR (0x4d204d4f5202), rev: 0x40, serial number: 0x010012C0
Manufacturing date: ? 2013
CID: 65646F4D 204D4F52 02400100 12C000F4
Bad CID detected, eMMC might be damaged !!!
CSD: D07FFF32 0F59007F F6DB8000 1E40001C
Bad CSD detected, eMMC might be damaged !!!
EXT_CSD revision: 1.5 (MMC v4.41)
Failed to switch partition to 3, error code: 0
CMD8 error, cmd response: 0x900, card state: 4 (Card is in transfer state)
Error: failed to switch to RPMB partition.
Partition info:
Boot1: 2 MiB
Boot2: 2 MiB
RPMB: 128 KiB
User area: 128 MiB(134,217,728 bytes)
Partition configuration: 0x78
Boot acknowledge is sent during the boot operation
User area is enabled for boot
Partitioning support: 0x03
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
 

md asif792

Junior Member
Jan 19, 2021
1
0
CTG
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8843-1510
Boot version: 1.05, FW version: 1.14 (Aug 25 2021 04:56:05)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 1 bit (SDR 52MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: Card (removable) - MMC
Manufacturer ID: 0x02 (SanDisk)
Product name: SDM032 (0x53444d303332), rev: 0x90, serial number: 0xFFFFFFFF
Manufacturing date: Feb 2022
CID: 02000053 444D3033 3290FFFF FFFF29BC
CSD: 8C0F002A 015981E9 B6D9FC1F 8A4040AA
Failed to read EXT_CSD !!!


halep me
 

calvinpower

Member
Mar 21, 2020
12
4
HOME
Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-6294
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: QD63MB (0x514436334d42), rev: 0x03, serial number: 0x77C50672
Manufacturing date: Oct 2019
CID: 15010051 4436334D 420377C5 0672A6C8
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
Failed to read EXT_CSD !!!
D0 and rst shorted. try check
 

aftab_ansari5287

Super Moderator
Aug 16, 2019
2,415
3,204
INDIA
Skype
aftab_ansari5287
PayPal:

Donate money to this user
Pinout is ok but this error
Failed to read EXT_CSD !!!

Like Quote Reply
Whats the prob pinout is ok
untick Ext-Csd and flash it. The phone will not be affected by the absence of Ext-Csd flash. You can also set it manually.

you may try to set boot config manually or via preset menu in ext_csd tab according to your SoC platform.
 
  • Like
Reactions: Tahirshinwari
Top