I need help to revive the A530F which had MDM lock only to end up messing it. I got this guide on the net followed and even backed up as per instruction in the video (
) in the end i messed up somewhere. The first time i got this phone i had got the data below.
30.12.2020)
Microsoft Windows 10 (64 bit) build 19042 (10.0.19041.804
Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 36 MHz
CMD Pullup Level: 443 mV
CMD Active Level: 1195 mV
EMMC Device Information :
EMMC CID: 150100424A5444345200523F424BBxxx
EMMC CSD: D02701320F5903FFF6DBFFEF8E40xxxx
EMMC Manufacture : SAMSUNG , EMMC NAME: BJTD4R , HEX: 424A54443452 , S/N: 523Fxxx , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 11/2018
EMMC ROM 1 (Main User Data) Capacity: 29820 MB (000747C00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: BJTD4R_523F424B_20210314_134254.extcsd
EMMC Init completed.
Scanning soft partitions
GPT header is found and is valid
Partition: BOTA0, [000000400000 - 000000800000], size: 000000400000 (4.00 MB)
Partition: NA, [000000800000 - 000000C00000], size: 000000400000 (4.00 MB)
Partition: EFS, [000000C00000 - 000002000000], size: 000001400000 (20.0 MB)
Partition: CPEFS, [000002000000 - 000002800000], size: 000000800000 (8.00 MB)
Partition: CM, [000002800000 - 000003000000], size: 000000800000 (8.00 MB)
Partition: m9kefs1, [000003000000 - 000003400000], size: 000000400000 (4.00 MB)
Partition: m9kefs2, [000003400000 - 000003800000], size: 000000400000 (4.00 MB)
Partition: m9kefs3, [000003800000 - 000003C00000], size: 000000400000 (4.00 MB)
Partition: NAD_REFER, [000003C00000 - 000003D00000], size: 000000100000 (1.00 MB)
Partition: PARAM, [000003D00000 - 000004500000], size: 000000800000 (8.00 MB)
Partition: MISC, [000004500000 - 000004700000], size: 000000200000 (2.00 MB)
Partition: BOOT, [000004700000 - 000006700000], size: 000002000000 (32.0 MB)
Partition: RECOVERY, [000006700000 - 000008D00000], size: 000002600000 (38.0 MB)
Partition: BOTA1, [000008D00000 - 000009500000], size: 000000800000 (8.00 MB)
Partition: RADIO, [000009500000 - 00000C200000], size: 000002D00000 (45.0 MB)
Partition: PERSISTENT, [00000C200000 - 00000C280000], size: 000000080000 (512. KB)
Partition: STEADY, [00000C280000 - 00000C680000], size: 000000400000 (4.00 MB)
Partition: RESERVED2, [00000C680000 - 00000C800000], size: 000000180000 (1.50 MB)
Partition: SYSTEM, [00000C800000 - 000104800000], size: 0000F8000000 (3.88 GB)
Partition: CACHE, [000104800000 - 000114200000], size: 00000FA00000 (250. MB)
Partition: HIDDEN, [000114200000 - 000114700000], size: 000000500000 (5.00 MB)
Partition: OMR, [000114700000 - 000117900000], size: 000003200000 (50.0 MB)
Partition: CP_DEBUG, [000117900000 - 000117E00000], size: 000000500000 (5.00 MB)
Partition: NAD_FW, [000117E00000 - 000119200000], size: 000001400000 (20.0 MB)
Partition: USERDATA, [000119200000 - 000747600000], size: 00062E400000 (24.7 GB)
GPT header successfully parsed
Get firmware version
Too many errors. Enabling ResetBox mode
Error: Except: Mount [cache] failed PartType: LINUX
Error: Except: Mount [omr] failed PartType: LINUX
Error: Except: Mount [data] failed PartType: LINUX
Error: Except: Unmount [cache/] failed
Error: Except: Unmount [omr/] failed
Error: Except: Unmount [data/] failed
Error: File "build.prop" is corrupted
SECOND READ OUT
Easy Jtag Box Clasic suite v3.7.20. Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN2 Firmware... IO: 1800 mV
Box S/N: 447541118F10xxxx, ,FW Ver.: 02.53
CMD Pullup Level:444 mV
CMD Active Level:1197 mV
Box IO Level:1800 mV
CLK Rate:36000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 150100424A5444345200523F424Bxxxx
eMMC CSD : D02701320F5903FFF6DBFFEF8E40xxxx
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 11/2018 Rev.0x0
eMMC NAME: BJTD4R , S/N: 1379877xxxx
eMMC NAME (HEX): 424A5444xxxx
EMMC ROM1 (Main User Data) Capacity: 29820 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 kB
EMMC RPMB is not yet programmed (clear) or NO Error
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: BJTD4R_1379877451_20210314_1447.extcsd
Caution: invalid backup GPT header, but valid main header!
EFI Table seems to be corrupted (sizeOfPartitionEntries!=128) sizeOfPartitionEntries = 0
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: 3A3E000 sectors 29.1 GiB
Soft (Partitioned) Disk/Image size: 3A3DFBC sectors 29.1 GiB
Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B
Logical sector size: 0x200 bytes ,First/Last usable sector: 34,61071326
Partition info successfully found
------ Detected 25 partitions ------
P0 (BOTA0) [0x400000 0x400000] Size: 4.0MB
P1 (NA) [0x800000 0x400000] Size: 4.0MB
P2 (EFS) [0xc00000 0x1400000] Size: 20.0MB
P3 (CPEFS) [0x2000000 0x800000] Size: 8.0MB
P4 (CM) [0x2800000 0x800000] Size: 8.0MB
P5 (M9KEFS1) [0x3000000 0x400000] Size: 4.0MB
P6 (M9KEFS2) [0x3400000 0x400000] Size: 4.0MB
P7 (M9KEFS3) [0x3800000 0x400000] Size: 4.0MB
P8 (NAD_REFER) [0x3c00000 0x100000] Size: 1.0MB
P9 (PARAM) [0x3d00000 0x800000] Size: 8.0MB
P10 (MISC) [0x4500000 0x200000] Size: 2.0MB
P11 (BOOT) [0x4700000 0x2000000] Size: 32.0MB
P12 (RECOVERY) [0x6700000 0x2600000] Size: 38.0MB
P13 (BOTA1) [0x8d00000 0x800000] Size: 8.0MB
P14 (RADIO) [0x9500000 0x2d00000] Size: 45.0MB
P15 (PERSISTENT) [0xc200000 0x80000] Size: 512.0KB
P16 (STEADY) [0xc280000 0x400000] Size: 4.0MB
P17 (RESERVED2) [0xc680000 0x180000] Size: 1.500MB
P18 (SYSTEM) [0xc800000 0xf8000000] Size: 3.875GB
P19 (CACHE) [0x104800000 0xfa00000] Size: 250.0MB
P20 (HIDDEN) [0x114200000 0x500000] Size: 5.0MB
P21 (OMR) [0x114700000 0x3200000] Size: 50.0MB
P22 (CP_DEBUG) [0x117900000 0x500000] Size: 5.0MB
P23 (NAD_FW) [0x117e00000 0x1400000] Size: 20.0MB
P24 (USERDATA) [0x119200000 0x62e400000] Size: 24.722GB
------------------------------------
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x000C800000 (3.875GB)
Short EXT fs info:
Size: 3.842GB
Block size: 4.0KB
Inode size: 256
Inodes: 251968
Short Android info:
Blocks Reading Error (0x66679000 , 2 , Reason: DATA RCV CRC Error )
Build ID: PPR1.180610.011
Display Build ID: PPR1.180610.011.A530FXXSCCTE1
Release Incremental ID: A530FXXSCCTE1
Release Base ID: 9
Security Path: 2020-05-01
Device Model: SM-A530F
Device Manufacturer: samsung
Product ID: jackpotlte
Device Name A: jackpotltexx
Device Name B: jackpotlte
Architecture ABI: arm64-v8a
Device manufacturer: samsung
Build Description: jackpotltexx-user 9 PPR1.180610.011 A530FXXSCCTE1 release-keys
PDA ver.: A530FXXSCCTE1
FRP Partition Path: /dev/block/persistent
Backup saved: BuildProp_20210314_1447.txt
---------------------------------------------
Detected USERDATA USERDATA : 0x0119200000 (24.722GB)
Blocks Reading Error (0x119200400 , 2 , Reason: DATA RCV CRC Error )
Unable to mount USERDATA , code : 5
Userdata Superblock contents::
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
Done.
THIRD READ OUT
ANDROID FRP CLEAR Checking security ...
Running:Format FRP Partition...
Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN2 Firmware... IO: 1800 mV
Box S/N: 447541118F1xxxxx, ,FW Ver.: 02.53
CMD Pullup Level:444 mV
CMD Active Level:1195 mV
Box IO Level:1800 mV
CLK Rate:36000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 150100424A5444345200523F424BB5A7
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 11/2018 Rev.0x0
eMMC NAME: BJTD4R , S/N: 1379877xxxxx
eMMC NAME (HEX): 424A544xxxxx
EMMC ROM1 (Main User Data) Capacity: 29820 MB , 0x3A3E000 pages , 0x747C00000 bytes
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 kB
EMMC RPMB is not yet programmed (clear) or NO Error
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Caution: invalid backup GPT header, but valid main header!
EFI Table seems to be corrupted (sizeOfPartitionEntries!=128) sizeOfPartitionEntries = 0
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: 3A3E000 sectors 29.1 GiB
Soft (Partitioned) Disk/Image size: 3A3DFBC sectors 29.1 GiB
Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B
Logical sector size: 0x200 bytes ,First/Last usable sector: 34,61071326
Partition info successfully found
Formatting FRP...
Detected LINUX(Android) PERSISTENT : 0x000C200000 (512.0KB) formatting...
Done.
Detected LINUX(Android) CACHE : 0x0104800000 (250.0MB) , formatting...
Done.
Detected LINUX(Android) USERDATA : 0x0119200000 (24.722GB) , formatting...
Done.
Done.
Done.
FOURTH READOUT
Clear PIN /GST /PASS Checking security ...
Running:Reset PIN/PASS/GESTURE Locks
Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN2 Firmware... IO: 1800 mV
Box S/N: 447541118F1xxxx, ,FW Ver.: 02.53
CMD Pullup Level:445 mV
CMD Active Level:1196 mV
Box IO Level:1800 mV
CLK Rate:36000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 150100424A5444345200523F424BB5A7
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 11/2018 Rev.0x0
eMMC NAME: BJTD4R , S/N: 137987xxxx
eMMC NAME (HEX): 424A5444xxxx
EMMC ROM1 (Main User Data) Capacity: 29820 MB , 0x3A3E000 pages , 0x747C00000 bytes
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 kB
EMMC RPMB is not yet programmed (clear) or NO Error
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Caution: invalid backup GPT header, but valid main header!
EFI Table seems to be corrupted (sizeOfPartitionEntries!=128) sizeOfPartitionEntries = 0
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: 3A3E000 sectors 29.1 GiB
Soft (Partitioned) Disk/Image size: 3A3DFBC sectors 29.1 GiB
Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B
Logical sector size: 0x200 bytes ,First/Last usable sector: 34,61071326
Partition info successfully found
------ Android information ------
Detected LINUX(Android) USERDATA : 0x0119200000 (24.722GB)
Mount EXT4 fs...
Blocks Reading Error (0x119200400 , 2 , Reason: DATA RCV CRC Error )
Unable to mount USER , code : 5
---------------------------------------------
Done.
NOW AFTER TRYING EVERYTHING I THOUGHT WOULD REVIVE THE PHONE AM STUCK AT SCANING SOFT PARTITION, MAY SOMEONE HELP AND GUIDE ME ,I STILL GOT THE BACK UP,BELOW IS THE CURRENT LOG
Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 24 MHz
CMD Pullup Level: 457 mV
CMD Active Level: 1374 mV
EMMC Device Information :
EMMC CID: 150100424A54443452000684ECE174F9
EMMC CSD: 902701320F5903FFF6DB7FE08A40403B
EMMC Manufacture : SAMSUNG , EMMC NAME: BJTD4R , HEX: 424A54443452 , S/N: 0684ECE1 , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 7/2017
EMMC ROM 1 (Main User Data) Capacity: 29804 MB (000746C00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000) Counter: 0 , Response: Maybe not clean
EMMC GP1 (GP Partition 1) Capacity: 8 MB , WR_REL (000000800000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: BJTD4R_0684ECE1_20210601_220738.extcsd
EMMC Init completed.
Scanning soft partitions
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #1
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #2
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #3
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #4
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #5
Too many errors. Reading has been stopped
30.12.2020)
Microsoft Windows 10 (64 bit) build 19042 (10.0.19041.804
Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 36 MHz
CMD Pullup Level: 443 mV
CMD Active Level: 1195 mV
EMMC Device Information :
EMMC CID: 150100424A5444345200523F424BBxxx
EMMC CSD: D02701320F5903FFF6DBFFEF8E40xxxx
EMMC Manufacture : SAMSUNG , EMMC NAME: BJTD4R , HEX: 424A54443452 , S/N: 523Fxxx , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 11/2018
EMMC ROM 1 (Main User Data) Capacity: 29820 MB (000747C00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: BJTD4R_523F424B_20210314_134254.extcsd
EMMC Init completed.
Scanning soft partitions
GPT header is found and is valid
Partition: BOTA0, [000000400000 - 000000800000], size: 000000400000 (4.00 MB)
Partition: NA, [000000800000 - 000000C00000], size: 000000400000 (4.00 MB)
Partition: EFS, [000000C00000 - 000002000000], size: 000001400000 (20.0 MB)
Partition: CPEFS, [000002000000 - 000002800000], size: 000000800000 (8.00 MB)
Partition: CM, [000002800000 - 000003000000], size: 000000800000 (8.00 MB)
Partition: m9kefs1, [000003000000 - 000003400000], size: 000000400000 (4.00 MB)
Partition: m9kefs2, [000003400000 - 000003800000], size: 000000400000 (4.00 MB)
Partition: m9kefs3, [000003800000 - 000003C00000], size: 000000400000 (4.00 MB)
Partition: NAD_REFER, [000003C00000 - 000003D00000], size: 000000100000 (1.00 MB)
Partition: PARAM, [000003D00000 - 000004500000], size: 000000800000 (8.00 MB)
Partition: MISC, [000004500000 - 000004700000], size: 000000200000 (2.00 MB)
Partition: BOOT, [000004700000 - 000006700000], size: 000002000000 (32.0 MB)
Partition: RECOVERY, [000006700000 - 000008D00000], size: 000002600000 (38.0 MB)
Partition: BOTA1, [000008D00000 - 000009500000], size: 000000800000 (8.00 MB)
Partition: RADIO, [000009500000 - 00000C200000], size: 000002D00000 (45.0 MB)
Partition: PERSISTENT, [00000C200000 - 00000C280000], size: 000000080000 (512. KB)
Partition: STEADY, [00000C280000 - 00000C680000], size: 000000400000 (4.00 MB)
Partition: RESERVED2, [00000C680000 - 00000C800000], size: 000000180000 (1.50 MB)
Partition: SYSTEM, [00000C800000 - 000104800000], size: 0000F8000000 (3.88 GB)
Partition: CACHE, [000104800000 - 000114200000], size: 00000FA00000 (250. MB)
Partition: HIDDEN, [000114200000 - 000114700000], size: 000000500000 (5.00 MB)
Partition: OMR, [000114700000 - 000117900000], size: 000003200000 (50.0 MB)
Partition: CP_DEBUG, [000117900000 - 000117E00000], size: 000000500000 (5.00 MB)
Partition: NAD_FW, [000117E00000 - 000119200000], size: 000001400000 (20.0 MB)
Partition: USERDATA, [000119200000 - 000747600000], size: 00062E400000 (24.7 GB)
GPT header successfully parsed
Get firmware version
Too many errors. Enabling ResetBox mode
Error: Except: Mount [cache] failed PartType: LINUX
Error: Except: Mount [omr] failed PartType: LINUX
Error: Except: Mount [data] failed PartType: LINUX
Error: Except: Unmount [cache/] failed
Error: Except: Unmount [omr/] failed
Error: Except: Unmount [data/] failed
Error: File "build.prop" is corrupted
SECOND READ OUT
Easy Jtag Box Clasic suite v3.7.20. Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN2 Firmware... IO: 1800 mV
Box S/N: 447541118F10xxxx, ,FW Ver.: 02.53
CMD Pullup Level:444 mV
CMD Active Level:1197 mV
Box IO Level:1800 mV
CLK Rate:36000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 150100424A5444345200523F424Bxxxx
eMMC CSD : D02701320F5903FFF6DBFFEF8E40xxxx
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 11/2018 Rev.0x0
eMMC NAME: BJTD4R , S/N: 1379877xxxx
eMMC NAME (HEX): 424A5444xxxx
EMMC ROM1 (Main User Data) Capacity: 29820 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 kB
EMMC RPMB is not yet programmed (clear) or NO Error
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: BJTD4R_1379877451_20210314_1447.extcsd
Caution: invalid backup GPT header, but valid main header!
EFI Table seems to be corrupted (sizeOfPartitionEntries!=128) sizeOfPartitionEntries = 0
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: 3A3E000 sectors 29.1 GiB
Soft (Partitioned) Disk/Image size: 3A3DFBC sectors 29.1 GiB
Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B
Logical sector size: 0x200 bytes ,First/Last usable sector: 34,61071326
Partition info successfully found
------ Detected 25 partitions ------
P0 (BOTA0) [0x400000 0x400000] Size: 4.0MB
P1 (NA) [0x800000 0x400000] Size: 4.0MB
P2 (EFS) [0xc00000 0x1400000] Size: 20.0MB
P3 (CPEFS) [0x2000000 0x800000] Size: 8.0MB
P4 (CM) [0x2800000 0x800000] Size: 8.0MB
P5 (M9KEFS1) [0x3000000 0x400000] Size: 4.0MB
P6 (M9KEFS2) [0x3400000 0x400000] Size: 4.0MB
P7 (M9KEFS3) [0x3800000 0x400000] Size: 4.0MB
P8 (NAD_REFER) [0x3c00000 0x100000] Size: 1.0MB
P9 (PARAM) [0x3d00000 0x800000] Size: 8.0MB
P10 (MISC) [0x4500000 0x200000] Size: 2.0MB
P11 (BOOT) [0x4700000 0x2000000] Size: 32.0MB
P12 (RECOVERY) [0x6700000 0x2600000] Size: 38.0MB
P13 (BOTA1) [0x8d00000 0x800000] Size: 8.0MB
P14 (RADIO) [0x9500000 0x2d00000] Size: 45.0MB
P15 (PERSISTENT) [0xc200000 0x80000] Size: 512.0KB
P16 (STEADY) [0xc280000 0x400000] Size: 4.0MB
P17 (RESERVED2) [0xc680000 0x180000] Size: 1.500MB
P18 (SYSTEM) [0xc800000 0xf8000000] Size: 3.875GB
P19 (CACHE) [0x104800000 0xfa00000] Size: 250.0MB
P20 (HIDDEN) [0x114200000 0x500000] Size: 5.0MB
P21 (OMR) [0x114700000 0x3200000] Size: 50.0MB
P22 (CP_DEBUG) [0x117900000 0x500000] Size: 5.0MB
P23 (NAD_FW) [0x117e00000 0x1400000] Size: 20.0MB
P24 (USERDATA) [0x119200000 0x62e400000] Size: 24.722GB
------------------------------------
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x000C800000 (3.875GB)
Short EXT fs info:
Size: 3.842GB
Block size: 4.0KB
Inode size: 256
Inodes: 251968
Short Android info:
Blocks Reading Error (0x66679000 , 2 , Reason: DATA RCV CRC Error )
Build ID: PPR1.180610.011
Display Build ID: PPR1.180610.011.A530FXXSCCTE1
Release Incremental ID: A530FXXSCCTE1
Release Base ID: 9
Security Path: 2020-05-01
Device Model: SM-A530F
Device Manufacturer: samsung
Product ID: jackpotlte
Device Name A: jackpotltexx
Device Name B: jackpotlte
Architecture ABI: arm64-v8a
Device manufacturer: samsung
Build Description: jackpotltexx-user 9 PPR1.180610.011 A530FXXSCCTE1 release-keys
PDA ver.: A530FXXSCCTE1
FRP Partition Path: /dev/block/persistent
Backup saved: BuildProp_20210314_1447.txt
---------------------------------------------
Detected USERDATA USERDATA : 0x0119200000 (24.722GB)
Blocks Reading Error (0x119200400 , 2 , Reason: DATA RCV CRC Error )
Unable to mount USERDATA , code : 5
Userdata Superblock contents::
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ................................;
Done.
THIRD READ OUT
ANDROID FRP CLEAR Checking security ...
Running:Format FRP Partition...
Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN2 Firmware... IO: 1800 mV
Box S/N: 447541118F1xxxxx, ,FW Ver.: 02.53
CMD Pullup Level:444 mV
CMD Active Level:1195 mV
Box IO Level:1800 mV
CLK Rate:36000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 150100424A5444345200523F424BB5A7
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 11/2018 Rev.0x0
eMMC NAME: BJTD4R , S/N: 1379877xxxxx
eMMC NAME (HEX): 424A544xxxxx
EMMC ROM1 (Main User Data) Capacity: 29820 MB , 0x3A3E000 pages , 0x747C00000 bytes
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 kB
EMMC RPMB is not yet programmed (clear) or NO Error
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Caution: invalid backup GPT header, but valid main header!
EFI Table seems to be corrupted (sizeOfPartitionEntries!=128) sizeOfPartitionEntries = 0
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: 3A3E000 sectors 29.1 GiB
Soft (Partitioned) Disk/Image size: 3A3DFBC sectors 29.1 GiB
Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B
Logical sector size: 0x200 bytes ,First/Last usable sector: 34,61071326
Partition info successfully found
Formatting FRP...
Detected LINUX(Android) PERSISTENT : 0x000C200000 (512.0KB) formatting...
Done.
Detected LINUX(Android) CACHE : 0x0104800000 (250.0MB) , formatting...
Done.
Detected LINUX(Android) USERDATA : 0x0119200000 (24.722GB) , formatting...
Done.
Done.
Done.
FOURTH READOUT
Clear PIN /GST /PASS Checking security ...
Running:Reset PIN/PASS/GESTURE Locks
Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN2 Firmware... IO: 1800 mV
Box S/N: 447541118F1xxxx, ,FW Ver.: 02.53
CMD Pullup Level:445 mV
CMD Active Level:1196 mV
Box IO Level:1800 mV
CLK Rate:36000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 150100424A5444345200523F424BB5A7
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 11/2018 Rev.0x0
eMMC NAME: BJTD4R , S/N: 137987xxxx
eMMC NAME (HEX): 424A5444xxxx
EMMC ROM1 (Main User Data) Capacity: 29820 MB , 0x3A3E000 pages , 0x747C00000 bytes
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 kB
EMMC RPMB is not yet programmed (clear) or NO Error
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Caution: invalid backup GPT header, but valid main header!
EFI Table seems to be corrupted (sizeOfPartitionEntries!=128) sizeOfPartitionEntries = 0
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: 3A3E000 sectors 29.1 GiB
Soft (Partitioned) Disk/Image size: 3A3DFBC sectors 29.1 GiB
Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B
Logical sector size: 0x200 bytes ,First/Last usable sector: 34,61071326
Partition info successfully found
------ Android information ------
Detected LINUX(Android) USERDATA : 0x0119200000 (24.722GB)
Mount EXT4 fs...
Blocks Reading Error (0x119200400 , 2 , Reason: DATA RCV CRC Error )
Unable to mount USER , code : 5
---------------------------------------------
Done.
NOW AFTER TRYING EVERYTHING I THOUGHT WOULD REVIVE THE PHONE AM STUCK AT SCANING SOFT PARTITION, MAY SOMEONE HELP AND GUIDE ME ,I STILL GOT THE BACK UP,BELOW IS THE CURRENT LOG
Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 24 MHz
CMD Pullup Level: 457 mV
CMD Active Level: 1374 mV
EMMC Device Information :
EMMC CID: 150100424A54443452000684ECE174F9
EMMC CSD: 902701320F5903FFF6DB7FE08A40403B
EMMC Manufacture : SAMSUNG , EMMC NAME: BJTD4R , HEX: 424A54443452 , S/N: 0684ECE1 , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 7/2017
EMMC ROM 1 (Main User Data) Capacity: 29804 MB (000746C00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000) Counter: 0 , Response: Maybe not clean
EMMC GP1 (GP Partition 1) Capacity: 8 MB , WR_REL (000000800000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: BJTD4R_0684ECE1_20210601_220738.extcsd
EMMC Init completed.
Scanning soft partitions
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #1
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #2
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #3
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #4
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #5
Too many errors. Reading has been stopped