JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser .
Z3X Team
Selected model: Infinix X6811 (Infinix Zero X) Operation: Erase FRP And Wipe Software version: 9.6 Erasing of partitions can damage your device. Make sure that you have a backup created. Continue? YES Connect Type-C to NONE... OK Host Power Off... OK Connect phone to [PC] in BROM/PRELOADER Mode Waiting for device... OK Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0] Device found at COM115 [PRELOADER] Open port... OK Send start cmd... OK Get HW code from device... 0813 Get sec config... OK [00000005] Active sec flags: [SBC DAA] Get HW & SW version from device... OK HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00 Detect chip [MT6785] Library Version [2] Select platform... OK Init BROM... OK Force Charge... OK Disable WatchDog Timer... OK Read Efuse error Force switch to BROM... OK Waiting for device... OK Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0] Device found at COM7 [BROM] Open port... OK Send start cmd... OK Get HW code from device... 0813 Get sec config... OK [000000E5] Active sec flags: [SBC DAA] Get HW & SW version from device... OK HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00 Detect chip [MT6785] LibUSB installed Library Version [2] Select platform... OK Init BROM... OK Force Charge... OK Disable WatchDog Timer... OK Release testpoint, waiting 2 seconds Advanced Bypass Security... OK Waiting for device... OK Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0] Device found at COM7 [BROM] Open port... OK Send start cmd... OK Get HW code from device... 0813 Get sec config... OK [000000E0] Active sec flags: [] Get HW & SW version from device... OK HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00 Detect chip [MT6785] Library Version [2] Select platform... OK Init BROM... OK Force Charge... OK Disable WatchDog Timer... OK Reopen port for libver2... OK Get ME ID... OK ME_ID = 0xE233CAFB, 0x67A2ED28, 0x80FCF189, 0x9663BBEA Get Chip ID... [MT6785] Get SOC ID... [C51CA3D4FCEFB9D4D9F19BBC7ECDD29AB1CB49E74EAB4CA64F1E1CE68165C4C1] Get sec config... OK [000000E0] Load DownloadAgent... OK Search DA... OK [12] Send preloader... OK Start preloader... OK Checking preloader answer... OK Send bootloader... OK Start bootloader... OK Wait for answer from bootloader... OK Send SYNC signal... OK Setup device enviroment... OK Setup device parametres... OK Receive DA SYNC signal... OK Set DA parametres... OK Get device connection agent... [BROM] Get device info... OK UFS CID (FW VER): H9HQ15AFAMBDAR (A043) Load EMI from phone... OK Parse EMI config... OK Init EXT RAM... OK Send 2nd DA... OK Get device info... OK UFS INFO: UFS_CID : H9HQ15AFAMBDAR UFS_FWVER : A043 BLOCK_SIZE: 0x0000001000 (4.00Kb) UFS_LU0 : 0x0000400000 (4.00Mb) UFS_LU1 : 0x0000400000 (4.00Mb) UFS_LU2 : 0x1DCB000000 (119.17Gb) RAM INFO: INT_SRAM: 0x0000080000 (512.00Kb) EXT_RAM : 0x0200000000 (8.00Gb) HEALTH: Pre EOL Info: normal DeviceLifeTimeEstA: 10% - 20% device life time used DeviceLifeTimeEstB: 0% - 10% device life time used Checking USB status... USB_HIGH_SPEED Read partitions info from phone... OK Checking A/B state... OK [A] Read product info... [EROFS] ... OK Product Brand : Infinix Product Manufacturer : INFINIX MOBILITY LIMITED Product Model : Infinix X6811 Product Name : X6811-GL Product Device : Infinix-X6811 Product Board : Infinix-X6811 Board Platform : mt6785 Build ID : RP1A.200720.011 Build Date : Thu Aug 24 20:10:02 CST 2023 Display ID : INFINIX-R-64-230824V997 Security Patch : 2023-08-05 Version SDK : 30 Version Release : 11 Version Codename : REL Firmware Version : 230824V1229 Userdata FS Type : F2FS Read partition "frp"... OK Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Infinix_X6811%20(Infinix%20Zero%20X)/FRP_BACKUP_(2025-9-25_18-9-3)/ Format FRP... [P1] OK Writting FRP data... OK Formatting "userdata" partition... [P1] OK Formatting "metadata" partition... [P1] OK Formatting "md_udc" partition... [P1] OK Creating default filesystems... [USERDATA: F2FS] ... OK Wipe data done!
