LG H810 DEAD BOOT REPAIR DONE

Status
Not open for further replies.

maanarman

Friend's Martview
Dec 1, 2016
2,908
385
karachi pakistan
Skype
maanarman
Sonork ID
100.1608345
Welcome to Medusa Pro Software version 1.3.2.
Started.
Reader #0: FT SCR2000 0
Reader #1: FT SCR2000 1
Reader #2: Generic EMV Smartcard Reader 0
Reader #3: Generic EMV Smartcard Reader 1

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Brand : LG
Model : H811
SRF : D:/JTAG/medusa + pro/medusa pro/LG_H811_EMMC.SRF
Voltage : 1.8V
Bus Mode : 1
Bus speed : Auto

Connecting...

ERROR[001]: Can not connect. No target device present.

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Brand : LG
Model : H811
SRF : D:/JTAG/medusa + pro/medusa pro/LG_H811_EMMC.SRF
Voltage : 2.8V
Bus Mode : 1
Bus speed : Auto

Connecting...
Device : Toshiba eMMC 032G74
Page size : 512 B
Block size : 512 B
Block count : 61071360
Size : 29.12 GB
---------------------------------------------------------------
CID Info

CID : 1101003033324737340052553F4E4209
Manufacturer ID : 0X11
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X00
Product name : 032G74
Product revision : 0.0
Product serial number : (hex) 52553F4E
Manufacturing date : 04/2015
---------------------------------------------------------------
CSD Info

CSD : D02700320F5903FFFFFFFFE78640009B
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 15 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info

Revision 1.7 (for MMC v5.0, v5.01)
Erase block size : 4096 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes
Boot partition enable : Device not boot enabled (default)

Partition config : 00000000
Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 15269888 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x0
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b
Backup EXT_CSD saved to file C:/Program Files/Medusa Pro Software/EXT_CSD Backups/032G74_02_03_2017_20_20_19.bin.
Connect successful.
---------------------------------------------------------------
SW: 1.3.2; FW: 1.15.
Opening E:/LG/H810 downgrad will dead/LGH810AT-01-V21y-310-410-JUN-20-2016-ARB03+0.tot file...
Signature OK.
Signature 2 OK.
Open file "E:/LG/H810 downgrad will dead/LGH810AT-01-V21y-310-410-JUN-20-2016-ARB03+0.tot".
Write data verification is enabled.
Writing. Please wait...
Writing partition PrimaryGPT... Done.
Writing partition modem... Done.
Writing partition pmic... Done.
Writing partition sbl1... Done.
Writing partition tz... Done.
Writing partition sdi... Done.
Writing partition hyp... Done.
Writing partition rpm... Done.
Writing partition aboot... Done.
Writing partition sbl1bak... Done.
Writing partition pmicbak... Done.
Writing partition tzbak... Done.
Writing partition hypbak... Done.
Writing partition rpmbak... Done.
Writing partition abootbak... Done.
Writing partition sdibak... Done.
Writing partition apdp... Done.
Writing partition msadp... Done.
Writing partition persist... Done.
Writing partition sec... Done.
Writing partition laf... Done.
Writing partition boot... Done.
Writing partition recovery... Done.
Writing partition raw_resources... Done.
Writing partition raw_resourcesbak... Done.
Writing partition felica... Done.
Writing partition factory... Done.
Writing is finished.
SW: 1.3.2; FW: 1.15.




THANKS TO JAMIL MOBILE
 

sunnyhoney323

Junior Member
Dec 25, 2016
1
2
peshawar
i have same model h810 after flash dead i connect with emmc points but give error plz can you guide me how i can repair

Welcome to Medusa Pro Software version 1.3.5.

Started.

Reader #0: Generic EMV Smartcard Reader 0

Reader #1: Generic EMV Smartcard Reader 1



Please disconnect battery and USB cable.



Model Settings:

Interface : eMMC

Voltage : 2.8V

Bus Mode : 1

Bus speed : Auto



Connecting...



ERROR[001]: Can not connect. No target device present.



Please disconnect battery and USB cable.



Model Settings:

Interface : eMMC

Voltage : 2.8V

Bus Mode : 1

Bus speed : Auto



Connecting...



ERROR[001]: Can not connect. No target device present.
 
Status
Not open for further replies.
Top