MI Note 6 Pro Dead Fixed with Easy-Jtag

Jeethesh Kothari

Active Member
Jul 19, 2019
20
30
MI Note 6 Pro Dead after flashing wrong file
First Flashed with Qc Fire But still same
Code:
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device    : Xiaomi Redmi Note 6 Pro [tulip]
Software    : PKQ1.180904.001, V10.3.2.0.PEKMIXM [Fri Apr 26 19:32:58 WIB 2019]
Android Ver.    : 9
Patch Level    : 2019-04-05
USERDATA    : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.6

Operation    : Flash
Checking for existing devices...Found
Port    : Qualcomm HS-USB QDLoader 9008 (COM99)
Driver Info    : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [storsec.mbn] -> [storsec] ...Done
Writing [storsec.mbn] -> [storsecbak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [pmic.elf] -> [pmic] ...Done
Writing [pmic.elf] -> [pmicbak] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [abl.elf] -> [abl] ...Done
Writing [abl.elf] -> [ablbak] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecapp] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecappbak] ...Done
Writing [keymaster64.mbn] -> [keymaster] ...Done
Writing [keymaster64.mbn] -> [keymasterbak] ...Done
Writing [BTFM.bin] -> [bluetooth] ...Done
Writing [xbl.elf] -> [xbl] ...Done
Writing [xbl.elf] -> [xblbak] ...Done
Writing [dspso.bin] -> [dsp] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cache.img ] -> [cache]...Done
Writing [system.img ] -> [system]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [cust.img ] -> [cust]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Resetting device...Done
Operation Finished.
QcFire Ver. 4.6
Removed EMCP and Pogrammed with EasyJtag Job Done

READ INFO


Writing Backuped Security
 
Last edited:

Instant Mobile

Active Member
Dec 9, 2016
25
8
kolkata
MI Note 6 Pro Dead after flashing wrong file
First Flashed with Qc Fire But still same
Code:
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device    : Xiaomi Redmi Note 6 Pro [tulip]
Software    : PKQ1.180904.001, V10.3.2.0.PEKMIXM [Fri Apr 26 19:32:58 WIB 2019]
Android Ver.    : 9
Patch Level    : 2019-04-05
USERDATA    : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.6

Operation    : Flash
Checking for existing devices...Found
Port    : Qualcomm HS-USB QDLoader 9008 (COM99)
Driver Info    : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [storsec.mbn] -> [storsec] ...Done
Writing [storsec.mbn] -> [storsecbak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [pmic.elf] -> [pmic] ...Done
Writing [pmic.elf] -> [pmicbak] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [abl.elf] -> [abl] ...Done
Writing [abl.elf] -> [ablbak] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecapp] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecappbak] ...Done
Writing [keymaster64.mbn] -> [keymaster] ...Done
Writing [keymaster64.mbn] -> [keymasterbak] ...Done
Writing [BTFM.bin] -> [bluetooth] ...Done
Writing [xbl.elf] -> [xbl] ...Done
Writing [xbl.elf] -> [xblbak] ...Done
Writing [dspso.bin] -> [dsp] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cache.img ] -> [cache]...Done
Writing [system.img ] -> [system]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [cust.img ] -> [cust]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Resetting device...Done
Operation Finished.
QcFire Ver. 4.6
Removed EMCP and Pogrammed with EasyJtag Job Done

READ INFO


Writing Backuped Security


Need Pinout Plz..........................
 

Mohd faeem

Member
Oct 3, 2019
5
1
How to connect emcp mi note 6 pro moorc 13 in 1
not ditect emcp how to bga ?
but set fully on and restart
how to connect easy jtag plus
 

abu14

Member
Jul 17, 2019
5
0
tirunelveli
MI Note 6 Pro Dead after flashing wrong file
First Flashed with Qc Fire But still same
Code:
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device    : Xiaomi Redmi Note 6 Pro [tulip]
Software    : PKQ1.180904.001, V10.3.2.0.PEKMIXM [Fri Apr 26 19:32:58 WIB 2019]
Android Ver.    : 9
Patch Level    : 2019-04-05
USERDATA    : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.6

Operation    : Flash
Checking for existing devices...Found
Port    : Qualcomm HS-USB QDLoader 9008 (COM99)
Driver Info    : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [storsec.mbn] -> [storsec] ...Done
Writing [storsec.mbn] -> [storsecbak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [pmic.elf] -> [pmic] ...Done
Writing [pmic.elf] -> [pmicbak] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [abl.elf] -> [abl] ...Done
Writing [abl.elf] -> [ablbak] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecapp] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecappbak] ...Done
Writing [keymaster64.mbn] -> [keymaster] ...Done
Writing [keymaster64.mbn] -> [keymasterbak] ...Done
Writing [BTFM.bin] -> [bluetooth] ...Done
Writing [xbl.elf] -> [xbl] ...Done
Writing [xbl.elf] -> [xblbak] ...Done
Writing [dspso.bin] -> [dsp] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cache.img ] -> [cache]...Done
Writing [system.img ] -> [system]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [cust.img ] -> [cust]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Resetting device...Done
Operation Finished.
QcFire Ver. 4.6
Removed EMCP and Pogrammed with EasyJtag Job Done

READ INFO


Writing Backuped Security
bro Redmi note 6 pro isp pinout
 

guddu1555

Junior Member
Dec 25, 2019
3
0
What is exact partition backup for security ? can you guide

like modemst1, modemst2, persist, persistbak and modem anything more need to backup for qualcomm device security ?
 

AnbazhaganC

Junior Member
Apr 19, 2017
2
1
india
MI Note 6 Pro Dead after flashing wrong file
First Flashed with Qc Fire But still same
Code:
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device    : Xiaomi Redmi Note 6 Pro [tulip]
Software    : PKQ1.180904.001, V10.3.2.0.PEKMIXM [Fri Apr 26 19:32:58 WIB 2019]
Android Ver.    : 9
Patch Level    : 2019-04-05
USERDATA    : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.6

Operation    : Flash
Checking for existing devices...Found
Port    : Qualcomm HS-USB QDLoader 9008 (COM99)
Driver Info    : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [storsec.mbn] -> [storsec] ...Done
Writing [storsec.mbn] -> [storsecbak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [pmic.elf] -> [pmic] ...Done
Writing [pmic.elf] -> [pmicbak] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [abl.elf] -> [abl] ...Done
Writing [abl.elf] -> [ablbak] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecapp] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecappbak] ...Done
Writing [keymaster64.mbn] -> [keymaster] ...Done
Writing [keymaster64.mbn] -> [keymasterbak] ...Done
Writing [BTFM.bin] -> [bluetooth] ...Done
Writing [xbl.elf] -> [xbl] ...Done
Writing [xbl.elf] -> [xblbak] ...Done
Writing [dspso.bin] -> [dsp] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cache.img ] -> [cache]...Done
Writing [system.img ] -> [system]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [cust.img ] -> [cust]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Resetting device...Done
Operation Finished.
QcFire Ver. 4.6
Removed EMCP and Pogrammed with EasyJtag Job Done

READ INFO


Writing redmi note 6 pro boot file please