MI Note 6 Pro Dead Fixed with Easy-Jtag

mdShareef

Junior Member
Sep 15, 2019
2
1
MI Note 6 Pro Dead after flashing wrong file
First Flashed with Qc Fire But still same
Code:
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device    : Xiaomi Redmi Note 6 Pro [tulip]
Software    : PKQ1.180904.001, V10.3.2.0.PEKMIXM [Fri Apr 26 19:32:58 WIB 2019]
Android Ver.    : 9
Patch Level    : 2019-04-05
USERDATA    : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.6

Operation    : Flash
Checking for existing devices...Found
Port    : Qualcomm HS-USB QDLoader 9008 (COM99)
Driver Info    : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [storsec.mbn] -> [storsec] ...Done
Writing [storsec.mbn] -> [storsecbak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [pmic.elf] -> [pmic] ...Done
Writing [pmic.elf] -> [pmicbak] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [abl.elf] -> [abl] ...Done
Writing [abl.elf] -> [ablbak] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecapp] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecappbak] ...Done
Writing [keymaster64.mbn] -> [keymaster] ...Done
Writing [keymaster64.mbn] -> [keymasterbak] ...Done
Writing [BTFM.bin] -> [bluetooth] ...Done
Writing [xbl.elf] -> [xbl] ...Done
Writing [xbl.elf] -> [xblbak] ...Done
Writing [dspso.bin] -> [dsp] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cache.img ] -> [cache]...Done
Writing [system.img ] -> [system]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [cust.img ] -> [cust]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Resetting device...Done
Operation Finished.
QcFire Ver. 4.6

Removed EMCP and Pogrammed with EasyJtag Job Done

READ INFO


Writing Backuped Security
MI note 6 Pro isp pin
 

Kh Alamin

Junior Member
Oct 20, 2020
4
0
Gazipur, Bangladesh
MI Note 6 Pro Dead after flashing wrong file
First Flashed with Qc Fire But still same
Code:
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device    : Xiaomi Redmi Note 6 Pro [tulip]
Software    : PKQ1.180904.001, V10.3.2.0.PEKMIXM [Fri Apr 26 19:32:58 WIB 2019]
Android Ver.    : 9
Patch Level    : 2019-04-05
USERDATA    : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.6

Operation    : Flash
Checking for existing devices...Found
Port    : Qualcomm HS-USB QDLoader 9008 (COM99)
Driver Info    : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [storsec.mbn] -> [storsec] ...Done
Writing [storsec.mbn] -> [storsecbak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [pmic.elf] -> [pmic] ...Done
Writing [pmic.elf] -> [pmicbak] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [abl.elf] -> [abl] ...Done
Writing [abl.elf] -> [ablbak] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecapp] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecappbak] ...Done
Writing [keymaster64.mbn] -> [keymaster] ...Done
Writing [keymaster64.mbn] -> [keymasterbak] ...Done
Writing [BTFM.bin] -> [bluetooth] ...Done
Writing [xbl.elf] -> [xbl] ...Done
Writing [xbl.elf] -> [xblbak] ...Done
Writing [dspso.bin] -> [dsp] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cache.img ] -> [cache]...Done
Writing [system.img ] -> [system]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [cust.img ] -> [cust]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Resetting device...Done
Operation Finished.
QcFire Ver. 4.6

Removed EMCP and Pogrammed with EasyJtag Job Done

READ INFO


Writing Backuped Security
 

Kh Alamin

Junior Member
Oct 20, 2020
4
0
Gazipur, Bangladesh
MI Note 6 Pro Dead after flashing wrong file
First Flashed with Qc Fire But still same
Code:
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device    : Xiaomi Redmi Note 6 Pro [tulip]
Software    : PKQ1.180904.001, V10.3.2.0.PEKMIXM [Fri Apr 26 19:32:58 WIB 2019]
Android Ver.    : 9
Patch Level    : 2019-04-05
USERDATA    : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.6

Operation    : Flash
Checking for existing devices...Found
Port    : Qualcomm HS-USB QDLoader 9008 (COM99)
Driver Info    : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [storsec.mbn] -> [storsec] ...Done
Writing [storsec.mbn] -> [storsecbak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [pmic.elf] -> [pmic] ...Done
Writing [pmic.elf] -> [pmicbak] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [abl.elf] -> [abl] ...Done
Writing [abl.elf] -> [ablbak] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecapp] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecappbak] ...Done
Writing [keymaster64.mbn] -> [keymaster] ...Done
Writing [keymaster64.mbn] -> [keymasterbak] ...Done
Writing [BTFM.bin] -> [bluetooth] ...Done
Writing [xbl.elf] -> [xbl] ...Done
Writing [xbl.elf] -> [xblbak] ...Done
Writing [dspso.bin] -> [dsp] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cache.img ] -> [cache]...Done
Writing [system.img ] -> [system]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [cust.img ] -> [cust]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Resetting device...Done
Operation Finished.
QcFire Ver. 4.6

Removed EMCP and Pogrammed with EasyJtag Job Done

READ INFO


Writing Backuped Security
please give me security bacup file
 

javed.tak

Junior Member
Oct 24, 2019
3
0
MI Note 6 Pro Dead after flashing wrong file
First Flashed with Qc Fire But still same
Code:
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device    : Xiaomi Redmi Note 6 Pro [tulip]
Software    : PKQ1.180904.001, V10.3.2.0.PEKMIXM [Fri Apr 26 19:32:58 WIB 2019]
Android Ver.    : 9
Patch Level    : 2019-04-05
USERDATA    : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.6

Operation    : Flash
Checking for existing devices...Found
Port    : Qualcomm HS-USB QDLoader 9008 (COM99)
Driver Info    : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [storsec.mbn] -> [storsec] ...Done
Writing [storsec.mbn] -> [storsecbak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [pmic.elf] -> [pmic] ...Done
Writing [pmic.elf] -> [pmicbak] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [abl.elf] -> [abl] ...Done
Writing [abl.elf] -> [ablbak] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecapp] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecappbak] ...Done
Writing [keymaster64.mbn] -> [keymaster] ...Done
Writing [keymaster64.mbn] -> [keymasterbak] ...Done
Writing [BTFM.bin] -> [bluetooth] ...Done
Writing [xbl.elf] -> [xbl] ...Done
Writing [xbl.elf] -> [xblbak] ...Done
Writing [dspso.bin] -> [dsp] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cache.img ] -> [cache]...Done
Writing [system.img ] -> [system]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [cust.img ] -> [cust]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Resetting device...Done
Operation Finished.
QcFire Ver. 4.6

Removed EMCP and Pogrammed with EasyJtag Job Done

READ INFO


Writing Backuped Security
Please share dump
 

javed.tak

Junior Member
Oct 24, 2019
3
0
MI Note 6 Pro Dead after flashing wrong file
First Flashed with Qc Fire But still same
Code:
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device    : Xiaomi Redmi Note 6 Pro [tulip]
Software    : PKQ1.180904.001, V10.3.2.0.PEKMIXM [Fri Apr 26 19:32:58 WIB 2019]
Android Ver.    : 9
Patch Level    : 2019-04-05
USERDATA    : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.6

Operation    : Flash
Checking for existing devices...Found
Port    : Qualcomm HS-USB QDLoader 9008 (COM99)
Driver Info    : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID    : E1C00C00 [8996] 00000000
OPK_DATA    : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_016]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware    : MSM8996, eMMC, 64 GB
LU Count    : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info    : In: 65536 [4096], Out: 131072, Sector Size: 512
Writing [storsec.mbn] -> [storsec] ...Done
Writing [storsec.mbn] -> [storsecbak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [pmic.elf] -> [pmic] ...Done
Writing [pmic.elf] -> [pmicbak] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [abl.elf] -> [abl] ...Done
Writing [abl.elf] -> [ablbak] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecapp] ...Done
Writing [mdtpsecapp.mbn] -> [mdtpsecappbak] ...Done
Writing [keymaster64.mbn] -> [keymaster] ...Done
Writing [keymaster64.mbn] -> [keymasterbak] ...Done
Writing [BTFM.bin] -> [bluetooth] ...Done
Writing [xbl.elf] -> [xbl] ...Done
Writing [xbl.elf] -> [xblbak] ...Done
Writing [dspso.bin] -> [dsp] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cache.img ] -> [cache]...Done
Writing [system.img ] -> [system]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [cust.img ] -> [cust]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Resetting device...Done
Operation Finished.
QcFire Ver. 4.6

Removed EMCP and Pogrammed with EasyJtag Job Done

READ INFO


Writing Backuped Security
please share dump
 
Top