Connect phone in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM70 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0x740946E1, 0xE10433C0, 0xD257A5C0, 0x7B8228A9
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Get device info... OK
UFS CID (FW VER): MT128GAXAU2U22 (0107)
Send preloader... OK
Load DownloadAgent... OK
Search DA... OK [14]
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : MT128GAXAU2U22
UFS_FWVER : 0107
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... error(0)
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Repairing IMEI...
IMEI 1: 863881051666xxx
IMEI 2: 863881051666xxx
Write IMEI and patch CERT [NVDATA]... OK
Unknown OPPO model!
Selected model: OPPO CPH2483 (Oppo A78 5G)
Operation: Repair
Software version: 6.2
Work ID: 15606966
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM70 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0x740946E1, 0xE10433C0, 0xD257A5C0, 0x7B8228A9
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Get device info... OK
UFS CID (FW VER): MT128GAXAU2U22 (0107)
Send preloader... OK
Load DownloadAgent... OK
Search DA... OK [14]
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : MT128GAXAU2U22
UFS_FWVER : 0107
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... error(0)
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Repairing IMEI...
IMEI 1: 863881051666xxx
IMEI 2: 863881051666xxx
Write IMEI and patch CERT [NVDATA]... OK
Unknown OPPO model!
Selected model: OPPO CPH2483 (Oppo A78 5G)
Operation: Repair
Software version: 6.2
Work ID: 15606966
