OPPO F11 CPH1911 FRP UNLOCK DONE 
Selected model: OPPO CPH1911 (OPPO F11)
Operation: Erase FRP And Wipe
Software version: 9.7
Erasing of partitions can damage your device.
Make sure that you have a backup created. Continue? YES
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM50 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM50 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xF892DA06, 0xED976B21, 0x1F9E1838, 0x65A777B3
Get Chip ID... [MT6771]
Get SOC ID... [8F1DFCF3981B7A34F05F1FB6634A12FBA46769D3DFE7F603A185C6EDF148D234]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [9]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68433861503E036124B5511647
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: hC8aP>
EMMC_ID : 0x90014A68433861503E036124B5511647
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000039000 (228.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: info not available
DeviceLifeTimeEstB: 20% - 30% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : oplus_mssi_64_cn
Product Name : sys_oplus_mssi_64_cn
Product Device : oplus_mssi_64_cn
Product Board : oppo6771
Board Platform : mt6771
Build ID : RP1A.200720.011
Build Date : Tue Jan 16 12:12:05 CST 2024
Display ID : RP1A.200720.011 release-keys
Security Patch : 2022-04-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1705377488980
Userdata FS Type : EXT4
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/OPPO_CPH1911%20(OPPO%20F11)/FRP_BACKUP_(2025-10-22_13-58-3)/
Format FRP... [P1] OK
Writting FRP data... OK
Formatting "userdata" partition... [P1] OK
Formatting "cache" partition... [P1] OK
Formatting "metadata" partition... [P1] OK
Creating default filesystems... [USERDATA: EXT4] ... [CACHE: EXT4] ... OK
Wipe data done!
Selected model: OPPO CPH1911 (OPPO F11)
Operation: Erase FRP And Wipe
Software version: 9.7
Erasing of partitions can damage your device.
Make sure that you have a backup created. Continue? YES
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM50 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM50 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xF892DA06, 0xED976B21, 0x1F9E1838, 0x65A777B3
Get Chip ID... [MT6771]
Get SOC ID... [8F1DFCF3981B7A34F05F1FB6634A12FBA46769D3DFE7F603A185C6EDF148D234]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [9]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68433861503E036124B5511647
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: hC8aP>
EMMC_ID : 0x90014A68433861503E036124B5511647
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000039000 (228.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: info not available
DeviceLifeTimeEstB: 20% - 30% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : oplus_mssi_64_cn
Product Name : sys_oplus_mssi_64_cn
Product Device : oplus_mssi_64_cn
Product Board : oppo6771
Board Platform : mt6771
Build ID : RP1A.200720.011
Build Date : Tue Jan 16 12:12:05 CST 2024
Display ID : RP1A.200720.011 release-keys
Security Patch : 2022-04-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1705377488980
Userdata FS Type : EXT4
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/OPPO_CPH1911%20(OPPO%20F11)/FRP_BACKUP_(2025-10-22_13-58-3)/
Format FRP... [P1] OK
Writting FRP data... OK
Formatting "userdata" partition... [P1] OK
Formatting "cache" partition... [P1] OK
Formatting "metadata" partition... [P1] OK
Creating default filesystems... [USERDATA: EXT4] ... [CACHE: EXT4] ... OK
Wipe data done!
