I have never been able to use the Pandora box since the day I bought it.
There are 4 or 5 other people around me who have the same problem.
Pandora box does not do any patch cert process on Xiaomi devices.
It gives missing lines while doing patch cert operation.
As you can see in the picture below and in the log, it does not give the
POSSIBLE BOOT CERT command.
Selected model: Xiaomi 21081111RG (11T)
Operation: Patch CERT
Software version: 3.8
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0950
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6893]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM331 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0950
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6893]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x518E09AF, 0x5FF7AC59, 0x964C1472, 0x3D1DE800
Get Chip ID... [MT6893]
Get SOC ID... [58D9D99AC9A18EEA73B36EAD778814334F17D70AB801F57623 5D9F7155FE1D00]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [19]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KLUDG4UHDC-B0E1 (0200)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KLUDG4UHDC-B0E1
UFS_FWVER : 0200
BLOCK_SIZE: 0x0000001000 (4,00Kb)
UFS_LU0 : 0x0000400000 (4,00Mb)
UFS_LU1 : 0x0000400000 (4,00Mb)
UFS_LU2 : 0x1DCB000000 (119,17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0100000000 (4,00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [A]
Read product info... OK
Product Brand : redmi
Product Manufacturer : Xiaomi
Product Model : missi
Product Name : missi
Product Device : missi
Product Board : agate
Board Platform : 6893
Build ID : SP1A.210812.016
Build Date : Fri Feb 18 19:27:07 CST 2022
Display ID : SP1A.210812.016
Security Patch : 2022-01-01
Version SDK : 31
Version Release : 12
Version Codename : REL
Firmware Version : V13.0.2.0.SKWMIXM
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Patch CERT [NVDATA]... OK
Patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.
There are 4 or 5 other people around me who have the same problem.
Pandora box does not do any patch cert process on Xiaomi devices.
It gives missing lines while doing patch cert operation.
As you can see in the picture below and in the log, it does not give the
POSSIBLE BOOT CERT command.
Selected model: Xiaomi 21081111RG (11T)
Operation: Patch CERT
Software version: 3.8
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0950
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6893]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM331 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0950
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6893]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x518E09AF, 0x5FF7AC59, 0x964C1472, 0x3D1DE800
Get Chip ID... [MT6893]
Get SOC ID... [58D9D99AC9A18EEA73B36EAD778814334F17D70AB801F57623 5D9F7155FE1D00]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [19]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KLUDG4UHDC-B0E1 (0200)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KLUDG4UHDC-B0E1
UFS_FWVER : 0200
BLOCK_SIZE: 0x0000001000 (4,00Kb)
UFS_LU0 : 0x0000400000 (4,00Mb)
UFS_LU1 : 0x0000400000 (4,00Mb)
UFS_LU2 : 0x1DCB000000 (119,17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0100000000 (4,00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [A]
Read product info... OK
Product Brand : redmi
Product Manufacturer : Xiaomi
Product Model : missi
Product Name : missi
Product Device : missi
Product Board : agate
Board Platform : 6893
Build ID : SP1A.210812.016
Build Date : Fri Feb 18 19:27:07 CST 2022
Display ID : SP1A.210812.016
Security Patch : 2022-01-01
Version SDK : 31
Version Release : 12
Version Codename : REL
Firmware Version : V13.0.2.0.SKWMIXM
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Patch CERT [NVDATA]... OK
Patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.