Z3X Post here successfully Unlocked / Repaired / Flashed Phones with Pandora Tool
- Thread starter saharsoft
- Start date
Z3X Team
Selected model: OPPO CPH1825 (OPPO F9)
Operation: Wipe Data
Software version: 9.12
There is a risk of data loss.
This procedure will erase all User Data
Make sure that you have a backup created. Continue? YES
Work ID: 100119544
Connect phone in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM (Android),usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM347 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0x75CF9EB2, 0xCFC7D7FA, 0x69679167, 0xF13C9BC2
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send preloader... OK
Load DownloadAgent... OK
Search DA... OK [9]
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: S0J9K9
EMMC_ID : 0x13014E53304A394B391005B9868585FF
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1D1F000000 (116.48Gb)
RAM INFO:
INT_SRAM: 0x0000039000 (228.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : OPPO
Product Manufacturer : OPPO
Product Model : OPPO F9
Product Name : CPH1823
Product Device : CPH1823
Product Board : oppo6771_18311
Board Platform : mt6771
Build ID : O11019
Build Date : Thu Nov 15 20:08:42 CST 2018
Display ID : CPH1823EX_11_A.11_181115
Security Patch : 2018-10-05
Version SDK : 27
Version Release : 8.1.0
Version Codename : REL
Firmware Version : 1542283722
Userdata FS Type : EXT4
Formatting "userdata" partition... [P1] OK
Formatting "cache" partition... [P1] OK
Formatting "metadata" partition... [P1] OK
Wipe data done!
Operation: Wipe Data
Software version: 9.12
There is a risk of data loss.
This procedure will erase all User Data
Make sure that you have a backup created. Continue? YES
Work ID: 100119544
Connect phone in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM (Android),usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM347 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0x75CF9EB2, 0xCFC7D7FA, 0x69679167, 0xF13C9BC2
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send preloader... OK
Load DownloadAgent... OK
Search DA... OK [9]
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: S0J9K9
EMMC_ID : 0x13014E53304A394B391005B9868585FF
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1D1F000000 (116.48Gb)
RAM INFO:
INT_SRAM: 0x0000039000 (228.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : OPPO
Product Manufacturer : OPPO
Product Model : OPPO F9
Product Name : CPH1823
Product Device : CPH1823
Product Board : oppo6771_18311
Board Platform : mt6771
Build ID : O11019
Build Date : Thu Nov 15 20:08:42 CST 2018
Display ID : CPH1823EX_11_A.11_181115
Security Patch : 2018-10-05
Version SDK : 27
Version Release : 8.1.0
Version Codename : REL
Firmware Version : 1542283722
Userdata FS Type : EXT4
Formatting "userdata" partition... [P1] OK
Formatting "cache" partition... [P1] OK
Formatting "metadata" partition... [P1] OK
Wipe data done!
Selected model: Honor CMA-LX2 (Honor X7)
Operation: Erase FRP
Software version: 9.12
Work ID: 100648091
Waiting for device... OK
Device found at COM418
Port: Qualcomm HS-USB QDLoader 9008
Open port... OK
Reading device info... OK
Serial Number: 2841857400
Sahara ver: 2
OEM PK HASH: 1816101F1302CF634F7002490E6742134F5FCDE05A7EAFF5BA7029AA0E69F9521E921A171A2F60A67BAEF26B81AE61EB
CPU: SM6225 (Snapdragon 680 4G)
Vendor: Honor
MSM HW ID: 001B80E101A40003
SBL SW Ver: 00000000
Prepare loader file... OK
Loader hash: EA552D84E4370E7E557C4D656301A4FF58939E38
Loader PK hash: 1816101F1302CF634F7002490E6742134F5FCDE05A7EAFF5BA7029AA0E69F9521E921A171A2F60A67BAEF26B81AE61EB
Loader version: 6.5
Sending loader... OK
FireHose initialization... OK
Detecting memory type... OK [UFS]
Get storage info... OK
Storage info:
Type: UFS
Name: HN8T05DEHKX073
Page size: 1000
Block size: 1000
Partition count: 6
LU0 size: 0x1D86800000 (118.10Gb)
LU1 size: 0x0000800000 (8.00Mb)
LU2 size: 0x0000800000 (8.00Mb)
LU3 size: 0x0000800000 (8.00Mb)
LU4 size: 0x0040800000 (1.01Gb)
LU5 size: 0x0002000000 (32.00Mb)
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : HONOR
Product Manufacturer : unknown
Product Model : CMA-LX2
Product Name : CMA-LX2
Product Device : HNCMA-Q
Product Board : bengal
Board Platform : bengal
Build ID : HONORCMA-L42CQ
Build Date : Tue Jun 6 15:57:58 CST 2023
Display ID : System 7.1.0(10PF)
Security Patch : 2023-06-01
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : eng.root.20230608.173300
Userdata FS Type : F2FS
Serial Number : H0136R225L004152
WLAN MAC : 08E021B4F316
BT MAC : 08E021B8C3A6
Build Number : CMA-L42CQ 7.1.0.132(C185E1R1P1)
Device Model : CMA-LX2
Android Version : 11
Custom Version : CMA-L42CQ-CUST 7.1.0.1(C185)
Base Version : CMA-LGRP10-OVS 4.2.0.291
Erase FRP... OK
Done!
Operation: Erase FRP
Software version: 9.12
Work ID: 100648091
Waiting for device... OK
Device found at COM418
Port: Qualcomm HS-USB QDLoader 9008
Open port... OK
Reading device info... OK
Serial Number: 2841857400
Sahara ver: 2
OEM PK HASH: 1816101F1302CF634F7002490E6742134F5FCDE05A7EAFF5BA7029AA0E69F9521E921A171A2F60A67BAEF26B81AE61EB
CPU: SM6225 (Snapdragon 680 4G)
Vendor: Honor
MSM HW ID: 001B80E101A40003
SBL SW Ver: 00000000
Prepare loader file... OK
Loader hash: EA552D84E4370E7E557C4D656301A4FF58939E38
Loader PK hash: 1816101F1302CF634F7002490E6742134F5FCDE05A7EAFF5BA7029AA0E69F9521E921A171A2F60A67BAEF26B81AE61EB
Loader version: 6.5
Sending loader... OK
FireHose initialization... OK
Detecting memory type... OK [UFS]
Get storage info... OK
Storage info:
Type: UFS
Name: HN8T05DEHKX073
Page size: 1000
Block size: 1000
Partition count: 6
LU0 size: 0x1D86800000 (118.10Gb)
LU1 size: 0x0000800000 (8.00Mb)
LU2 size: 0x0000800000 (8.00Mb)
LU3 size: 0x0000800000 (8.00Mb)
LU4 size: 0x0040800000 (1.01Gb)
LU5 size: 0x0002000000 (32.00Mb)
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : HONOR
Product Manufacturer : unknown
Product Model : CMA-LX2
Product Name : CMA-LX2
Product Device : HNCMA-Q
Product Board : bengal
Board Platform : bengal
Build ID : HONORCMA-L42CQ
Build Date : Tue Jun 6 15:57:58 CST 2023
Display ID : System 7.1.0(10PF)
Security Patch : 2023-06-01
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : eng.root.20230608.173300
Userdata FS Type : F2FS
Serial Number : H0136R225L004152
WLAN MAC : 08E021B4F316
BT MAC : 08E021B8C3A6
Build Number : CMA-L42CQ 7.1.0.132(C185E1R1P1)
Device Model : CMA-LX2
Android Version : 11
Custom Version : CMA-L42CQ-CUST 7.1.0.1(C185)
Base Version : CMA-LGRP10-OVS 4.2.0.291
Erase FRP... OK
Done!
Selected model: Spreadtrum Spreadtrum
Operation: Erase FRP
Software version: 9.12
Work ID: 101112584
Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM177
Port: USB\VID_1782&PID_4D00\6&25963C02&0&4
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: Tiger_T616_64
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: MA516W062793
Flash Type: EMMC
Read partitions info... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : serenity
Product Name : serenity
Product Device : serenity
Product Board : serenity
Board Platform : ums9230
Build ID : TP1A.220624.014
Build Date : Sat Jun 21 12:00:51 CST 2025
Display ID : TP1A.220624.014 release-keys
Security Patch : 2025-06-01
Version SDK : 35
Version Release : 15
Version Codename : REL
Firmware Version : A15.0.11.0.VGWMIXM
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Done!
Operation: Erase FRP
Software version: 9.12
Work ID: 101112584
Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM177
Port: USB\VID_1782&PID_4D00\6&25963C02&0&4
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: Tiger_T616_64
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: MA516W062793
Flash Type: EMMC
Read partitions info... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : serenity
Product Name : serenity
Product Device : serenity
Product Board : serenity
Board Platform : ums9230
Build ID : TP1A.220624.014
Build Date : Sat Jun 21 12:00:51 CST 2025
Display ID : TP1A.220624.014 release-keys
Security Patch : 2025-06-01
Version SDK : 35
Version Release : 15
Version Codename : REL
Firmware Version : A15.0.11.0.VGWMIXM
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Done!
Selected model: Xiaomi Redmi A2+ (Water)
Operation: Erase FRP
Software version: 9.13
Work ID: 101865169
Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM207 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM207 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x185521E9, 0x8322B01E, 0xA00A92F4, 0x52E09127
Get Chip ID... [MT6765]
Get SOC ID... [817B6BC41E25D4EDB11F2320D27721D07AD45421F30C3927819C242419B54F3E]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x9B010059325030333200436B525599B1
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: Y2P032
EMMC_ID : 0x9B010059325030333200436B525599B1
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0080000000 (2.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : water
Product Name : water_global
Product Device : water
Product Board : water
Board Platform : mt6765
Build ID : SP1A.210812.016
Build Date : Mon Aug 14 22:05:34 CST 2023
Display ID : 13 V14.0.15.0.TGOMIXM
Security Patch : 2023-08-01
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : V14.0.15.0.TGOMIXM
Userdata FS Type : F2FS
MiAcc Find Device : Disabled
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Xiaomi_Redmi%20A2%2B%20(Water)/FRP_BACKUP_(2025-12-16_16-52-45)/
Format FRP... [P1] OK
Writting FRP data... OK
Erase FRP done!
Operation: Erase FRP
Software version: 9.13
Work ID: 101865169
Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM207 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM207 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x185521E9, 0x8322B01E, 0xA00A92F4, 0x52E09127
Get Chip ID... [MT6765]
Get SOC ID... [817B6BC41E25D4EDB11F2320D27721D07AD45421F30C3927819C242419B54F3E]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x9B010059325030333200436B525599B1
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: Y2P032
EMMC_ID : 0x9B010059325030333200436B525599B1
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0080000000 (2.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : water
Product Name : water_global
Product Device : water
Product Board : water
Board Platform : mt6765
Build ID : SP1A.210812.016
Build Date : Mon Aug 14 22:05:34 CST 2023
Display ID : 13 V14.0.15.0.TGOMIXM
Security Patch : 2023-08-01
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : V14.0.15.0.TGOMIXM
Userdata FS Type : F2FS
MiAcc Find Device : Disabled
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Xiaomi_Redmi%20A2%2B%20(Water)/FRP_BACKUP_(2025-12-16_16-52-45)/
Format FRP... [P1] OK
Writting FRP data... OK
Erase FRP done!
Selected model: Tecno BD4 (Tecno Pop 5 LTE)
Operation: Erase FRP
Software version: 9.13
Work ID: 101972409
Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM177
Port: USB\VID_1782&PID_4D00\6&25963C02&0&4
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: SC9863A
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: 07547151C4008890
Read partitions info... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : TECNO
Product Manufacturer : TECNO MOBILE LIMITED
Product Model : TECNO BD4
Product Name : BD4-OP
Product Device : TECNO-BD4
Product Board : BD4
Board Platform : sp9863a
Build ID : RP1A.201005.001
Build Date : Sun Nov 13 18:19:37 WIB 2022
Display ID : BD4-SE656BCEF-RGo-OP-221113V15
Security Patch : 2022-11-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 221113V15
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Done!
Operation: Erase FRP
Software version: 9.13
Work ID: 101972409
Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM177
Port: USB\VID_1782&PID_4D00\6&25963C02&0&4
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: SC9863A
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: 07547151C4008890
Read partitions info... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : TECNO
Product Manufacturer : TECNO MOBILE LIMITED
Product Model : TECNO BD4
Product Name : BD4-OP
Product Device : TECNO-BD4
Product Board : BD4
Board Platform : sp9863a
Build ID : RP1A.201005.001
Build Date : Sun Nov 13 18:19:37 WIB 2022
Display ID : BD4-SE656BCEF-RGo-OP-221113V15
Security Patch : 2022-11-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 221113V15
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Done!