Redmi 6 Cereus phone dead after error

Andy7

Member
Nov 22, 2019
9
0
I try flash it Redmi 6 Cereus again, because after one flash(downgrade to 8.1 to antireloack) successfully it stuck in logo, I try two attemps and all successfully, but the not starting, still on stuck logo, now I try one 9.0 and give it this error of log below, result is dead phone and consume credits. UFI do you help me, please?

--------------------
name: MTK_PLATFORM_CFG
version: V1.1.2
platform: MT6765
project: cereus
storage: EMMC
bootChannel: MSDC_0
blockSize: 0x00020000
name: MTK_PLATFORM_CFG
version: V1.1.2
platform: MT6765
project: cereus
storage: EMMC
bootChannel: MSDC_0
blockSize: 0x00020000
MTK Preloader file info.
Found 8 supported eMMC CID:
[Samsung] GD6BMB 15010047 4436424D 42xxxxxx xxxxxxxx
[Micron] S0J9B7 13014E53 304A3942 37xxxxxx xxxxxxxx
[SK Hynix] hB8aP 90014A68 42386150 3Exxxxxx xxxxxxxx
[Samsung] QE63MB 15010051 4536334D 42xxxxxx xxxxxxxx
[SK Hynix] HAG4a2 90014A48 41473461 32xxxxxx xxxxxxxx
[Samsung] RH64AB 15010052 48363441 42xxxxxx xxxxxxxx
[SK Hynix] HCG8a4 90014A48 43473861 34xxxxxx xxxxxxxx
[Samsung] GP6BMB 15010047 5036424D 42xxxxxx xxxxxxxx
AUTH info: MTK, version: 1
BROM version[1]: 7.1917.3.0
DownloadAgent: MTK_AllInOne_DA[0].bin
hash: c8fa00811a246c975e865b14121d0f527fe674a2, size: 542.12 KiB
version: 3.3001.2018/04/12019/12/02 18:01:19, start addr: 0x40000800
Connecting to BootROM...
Power off the phone, disconnect and reconnect the battery(if possible) and connect USB cable...
Hold the VOL DOWN or VOL UP + DOWN(for newer model) to force MediaTek BootROM.
Scanning BootROM or Preloader port(30 s)... Done
Detected [BootROM] MediaTek USB Port (COM15)
Connection status: XHCI:HUB3:USB 2.00 High-Speed
USB Driver: [MediaTek Inc.] wdm_usb, version: 3.0.1504.0, date: 1-22-2015
Connecting Bootrom...
[SERVER] XIAOMI_FL [cereus,18806bb8a9094157] ref id: XF07102453583, cost: 4, your balance: 7
Sending Download Agent...
Platform: MT6765, Hw ver: 0xCA00, Sw ver: 0x0000
Secure ver: 0x00, BL ver: 0x00
Secure config: 0x00
SRAM size: 256 KiB
DRAM size: 768 MiB
SOC ID: 18806bb8a90941576d516bbe72335de01644dfe3bc1490ac3ebd246f96b1f940
ME ID: a8fcc0ee897e33ad89a971b6c217fbad
Storage type: eMMC
Card/BGA: BGA (Discrete embedded)
Manufacturer ID: 0x15 (Samsung)
Product name: RH64AB (0x524836344142), rev: 0x05, serial number: 0x507CD03B
Manufacturing date: jun 2018
CID: 15010052 48363441 4205507C D03B65A3
Capacity: 58.25 GiB(62,549,655,552 bytes)
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB (key exist)
User area: 58.24 GiB(62,537,072,640 bytes)
USB speed: High-Speed
Verifying SoC: passed
Verifying CID: passed
Writing preloader, size: 229.17 KiB
Writing recovery, size: 64 MiB
Writing md1img, size: 54.13 MiB
Writing spmfw, size: 50.86 KiB
Writing scp1, size: 551.08 KiB
Writing scp2, size: 551.08 KiB
Writing sspm_1, size: 422.64 KiB
Writing sspm_2, size: 422.64 KiB
Writing vbmeta, size: 4 KiB
Writing lk, size: 681.66 KiB
Writing lk2, size: 681.66 KiB
Writing boot, size: 64 MiB
Writing logo, size: 1.12 MiB
Writing odmdtbo, size: 16 MiB
Error: -1073610710 (STATUS_SEC_IMG_TYPE_MISMATCH)
The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
You have used 1 available XIAOMI_FL slot for this phone, you have 2 FREE slot left to try again in case this task fails.
We found that you have used XIAOMI_FL service with this phone at Thu, 28 Nov 2019 16:29:54 GMT.
Note that due to limited authorization slot, every authorization service will take cost.
Before using another authorization, please make sure the phone have a good working hardware and you are using the correct firmware.
You may retry the task for more times without further authorization as long as you don't unplug the USB cable, change brand or model selection or close the application.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 

zawtunkt

Active Member
Sep 26, 2019
33
11
I try flash it Redmi 6 Cereus again, because after one flash(downgrade to 8.1 to antireloack) successfully it stuck in logo, I try two attemps and all successfully, but the not starting, still on stuck logo, now I try one 9.0 and give it this error of log below, result is dead phone and consume credits. UFI do you help me, please?

--------------------
name: MTK_PLATFORM_CFG
version: V1.1.2
platform: MT6765
project: cereus
storage: EMMC
bootChannel: MSDC_0
blockSize: 0x00020000
name: MTK_PLATFORM_CFG
version: V1.1.2
platform: MT6765
project: cereus
storage: EMMC
bootChannel: MSDC_0
blockSize: 0x00020000
MTK Preloader file info.
Found 8 supported eMMC CID:
[Samsung] GD6BMB 15010047 4436424D 42xxxxxx xxxxxxxx
[Micron] S0J9B7 13014E53 304A3942 37xxxxxx xxxxxxxx
[SK Hynix] hB8aP 90014A68 42386150 3Exxxxxx xxxxxxxx
[Samsung] QE63MB 15010051 4536334D 42xxxxxx xxxxxxxx
[SK Hynix] HAG4a2 90014A48 41473461 32xxxxxx xxxxxxxx
[Samsung] RH64AB 15010052 48363441 42xxxxxx xxxxxxxx
[SK Hynix] HCG8a4 90014A48 43473861 34xxxxxx xxxxxxxx
[Samsung] GP6BMB 15010047 5036424D 42xxxxxx xxxxxxxx
AUTH info: MTK, version: 1
BROM version[1]: 7.1917.3.0
DownloadAgent: MTK_AllInOne_DA[0].bin
hash: c8fa00811a246c975e865b14121d0f527fe674a2, size: 542.12 KiB
version: 3.3001.2018/04/12019/12/02 18:01:19, start addr: 0x40000800
Connecting to BootROM...
Power off the phone, disconnect and reconnect the battery(if possible) and connect USB cable...
Hold the VOL DOWN or VOL UP + DOWN(for newer model) to force MediaTek BootROM.
Scanning BootROM or Preloader port(30 s)... Done
Detected [BootROM] MediaTek USB Port (COM15)
Connection status: XHCI:HUB3:USB 2.00 High-Speed
USB Driver: [MediaTek Inc.] wdm_usb, version: 3.0.1504.0, date: 1-22-2015
Connecting Bootrom...
[SERVER] XIAOMI_FL [cereus,18806bb8a9094157] ref id: XF07102453583, cost: 4, your balance: 7
Sending Download Agent...
Platform: MT6765, Hw ver: 0xCA00, Sw ver: 0x0000
Secure ver: 0x00, BL ver: 0x00
Secure config: 0x00
SRAM size: 256 KiB
DRAM size: 768 MiB
SOC ID: 18806bb8a90941576d516bbe72335de01644dfe3bc1490ac3ebd246f96b1f940
ME ID: a8fcc0ee897e33ad89a971b6c217fbad
Storage type: eMMC
Card/BGA: BGA (Discrete embedded)
Manufacturer ID: 0x15 (Samsung)
Product name: RH64AB (0x524836344142), rev: 0x05, serial number: 0x507CD03B
Manufacturing date: jun 2018
CID: 15010052 48363441 4205507C D03B65A3
Capacity: 58.25 GiB(62,549,655,552 bytes)
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB (key exist)
User area: 58.24 GiB(62,537,072,640 bytes)
USB speed: High-Speed
Verifying SoC: passed
Verifying CID: passed
Writing preloader, size: 229.17 KiB
Writing recovery, size: 64 MiB
Writing md1img, size: 54.13 MiB
Writing spmfw, size: 50.86 KiB
Writing scp1, size: 551.08 KiB
Writing scp2, size: 551.08 KiB
Writing sspm_1, size: 422.64 KiB
Writing sspm_2, size: 422.64 KiB
Writing vbmeta, size: 4 KiB
Writing lk, size: 681.66 KiB
Writing lk2, size: 681.66 KiB
Writing boot, size: 64 MiB
Writing logo, size: 1.12 MiB
Writing odmdtbo, size: 16 MiB
Error: -1073610710 (STATUS_SEC_IMG_TYPE_MISMATCH)
The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
You have used 1 available XIAOMI_FL slot for this phone, you have 2 FREE slot left to try again in case this task fails.
We found that you have used XIAOMI_FL service with this phone at Thu, 28 Nov 2019 16:29:54 GMT.
Note that due to limited authorization slot, every authorization service will take cost.
Before using another authorization, please make sure the phone have a good working hardware and you are using the correct firmware.
You may retry the task for more times without further authorization as long as you don't unplug the USB cable, change brand or model selection or close the application.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
format all download flash again CN rom
 

atstech

Active Member
Oct 8, 2018
32
3
Skype
atstech
I try flash it Redmi 6 Cereus again, because after one flash(downgrade to 8.1 to antireloack) successfully it stuck in logo, I try two attemps and all successfully, but the not starting, still on stuck logo, now I try one 9.0 and give it this error of log below, result is dead phone and consume credits. UFI do you help me, please?

--------------------
name: MTK_PLATFORM_CFG
version: V1.1.2
platform: MT6765
project: cereus
storage: EMMC
bootChannel: MSDC_0
blockSize: 0x00020000
name: MTK_PLATFORM_CFG
version: V1.1.2
platform: MT6765
project: cereus
storage: EMMC
bootChannel: MSDC_0
blockSize: 0x00020000
MTK Preloader file info.
Found 8 supported eMMC CID:
[Samsung] GD6BMB 15010047 4436424D 42xxxxxx xxxxxxxx
[Micron] S0J9B7 13014E53 304A3942 37xxxxxx xxxxxxxx
[SK Hynix] hB8aP 90014A68 42386150 3Exxxxxx xxxxxxxx
[Samsung] QE63MB 15010051 4536334D 42xxxxxx xxxxxxxx
[SK Hynix] HAG4a2 90014A48 41473461 32xxxxxx xxxxxxxx
[Samsung] RH64AB 15010052 48363441 42xxxxxx xxxxxxxx
[SK Hynix] HCG8a4 90014A48 43473861 34xxxxxx xxxxxxxx
[Samsung] GP6BMB 15010047 5036424D 42xxxxxx xxxxxxxx
AUTH info: MTK, version: 1
BROM version[1]: 7.1917.3.0
DownloadAgent: MTK_AllInOne_DA[0].bin
hash: c8fa00811a246c975e865b14121d0f527fe674a2, size: 542.12 KiB
version: 3.3001.2018/04/12019/12/02 18:01:19, start addr: 0x40000800
Connecting to BootROM...
Power off the phone, disconnect and reconnect the battery(if possible) and connect USB cable...
Hold the VOL DOWN or VOL UP + DOWN(for newer model) to force MediaTek BootROM.
Scanning BootROM or Preloader port(30 s)... Done
Detected [BootROM] MediaTek USB Port (COM15)
Connection status: XHCI:HUB3:USB 2.00 High-Speed
USB Driver: [MediaTek Inc.] wdm_usb, version: 3.0.1504.0, date: 1-22-2015
Connecting Bootrom...
[SERVER] XIAOMI_FL [cereus,18806bb8a9094157] ref id: XF07102453583, cost: 4, your balance: 7
Sending Download Agent...
Platform: MT6765, Hw ver: 0xCA00, Sw ver: 0x0000
Secure ver: 0x00, BL ver: 0x00
Secure config: 0x00
SRAM size: 256 KiB
DRAM size: 768 MiB
SOC ID: 18806bb8a90941576d516bbe72335de01644dfe3bc1490ac3ebd246f96b1f940
ME ID: a8fcc0ee897e33ad89a971b6c217fbad
Storage type: eMMC
Card/BGA: BGA (Discrete embedded)
Manufacturer ID: 0x15 (Samsung)
Product name: RH64AB (0x524836344142), rev: 0x05, serial number: 0x507CD03B
Manufacturing date: jun 2018
CID: 15010052 48363441 4205507C D03B65A3
Capacity: 58.25 GiB(62,549,655,552 bytes)
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB (key exist)
User area: 58.24 GiB(62,537,072,640 bytes)
USB speed: High-Speed
Verifying SoC: passed
Verifying CID: passed
Writing preloader, size: 229.17 KiB
Writing recovery, size: 64 MiB
Writing md1img, size: 54.13 MiB
Writing spmfw, size: 50.86 KiB
Writing scp1, size: 551.08 KiB
Writing scp2, size: 551.08 KiB
Writing sspm_1, size: 422.64 KiB
Writing sspm_2, size: 422.64 KiB
Writing vbmeta, size: 4 KiB
Writing lk, size: 681.66 KiB
Writing lk2, size: 681.66 KiB
Writing boot, size: 64 MiB
Writing logo, size: 1.12 MiB
Writing odmdtbo, size: 16 MiB
Error: -1073610710 (STATUS_SEC_IMG_TYPE_MISMATCH)
The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
You have used 1 available XIAOMI_FL slot for this phone, you have 2 FREE slot left to try again in case this task fails.
We found that you have used XIAOMI_FL service with this phone at Thu, 28 Nov 2019 16:29:54 GMT.
Note that due to limited authorization slot, every authorization service will take cost.
Before using another authorization, please make sure the phone have a good working hardware and you are using the correct firmware.
You may retry the task for more times without further authorization as long as you don't unplug the USB cable, change brand or model selection or close the application.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

HOW Come we are not getting this option in indian boxes? yesterday night i got the same flashing error mesage as this and suddenly the software crashed and i lost credits! how can i get my credits back pls inform?

Code:
You have used 1 available XIAOMI_FL slot for this phone, you have 2 FREE slot left to try again in case this task fails.

  We found that you have used XIAOMI_FL service with this phone at Thu, 28 Nov 2019 16:29:54 GMT.

  Note that due to limited authorization slot, every authorization service will take cost.
can anyone reply to me?
wbr
 
Top