Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8842-9075
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... CLK not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x13 (Micron)
Product name: S0J9B7 (0x53304a394237), rev: 0x10, serial number: 0x049B6F5A
Manufacturing date: Jul 2018
CID: 13014E53 304A3942 3710049B 6F5A758C
CSD: D05F0132 8F5913FF FFFFFFEF 964000A8
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 29.12 GiB(31,268,536,320 bytes)
Cache size: 2 MiB
Hardware reset function: 1
Partition configuration: 0x38
No boot acknowledge is sent (default)
User area is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
User area write protection: 0x10
Password protection features: enabled
Power-on write protection: possible
Permanent write protection: not possible
Lock status: not locked
ANDROID System Info:
platform: msm8953, cpu abi: armeabi-v7a
manufacturer: Xiaomi
board: ysl, name: ysl
brand: xiaomi, model: Redmi S2
build model list: Redmi S2
build id: OPM1.171019.011, version: 8.1.0 Oreo (OPM1.171019.011)
build description: ysl-user 8.1.0 OPM1.171019.011 V9.6.2.0.OEFMIFD release-keys
Internal storage: 2.90 GiB
crypto state: unencrypted
is this log phone ready to boot plz need to know before i remove the jumper.phone was dead on software i flash it with full file now it show this
Interface: UFI High-Speed
Serial number: 0011-8842-9075
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... CLK not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x13 (Micron)
Product name: S0J9B7 (0x53304a394237), rev: 0x10, serial number: 0x049B6F5A
Manufacturing date: Jul 2018
CID: 13014E53 304A3942 3710049B 6F5A758C
CSD: D05F0132 8F5913FF FFFFFFEF 964000A8
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 29.12 GiB(31,268,536,320 bytes)
Cache size: 2 MiB
Hardware reset function: 1
Partition configuration: 0x38
No boot acknowledge is sent (default)
User area is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
User area write protection: 0x10
Password protection features: enabled
Power-on write protection: possible
Permanent write protection: not possible
Lock status: not locked
ANDROID System Info:
platform: msm8953, cpu abi: armeabi-v7a
manufacturer: Xiaomi
board: ysl, name: ysl
brand: xiaomi, model: Redmi S2
build model list: Redmi S2
build id: OPM1.171019.011, version: 8.1.0 Oreo (OPM1.171019.011)
build description: ysl-user 8.1.0 OPM1.171019.011 V9.6.2.0.OEFMIFD release-keys
Internal storage: 2.90 GiB
crypto state: unencrypted
is this log phone ready to boot plz need to know before i remove the jumper.phone was dead on software i flash it with full file now it show this