mob stck on logo i try to find dump file but i did not then i write sctter file and reball but now mob i s dead any body tell me where im wrong
Y600-u20 daed after flsh emmc with scatter
- Thread starter moeezali
- Start date
Boot version: 1.04, FW version: 1.12 (Jun 7 2018 00:06:47)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 8 bit (HS SDR 52MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: H4G1d (0x483447316404), rev: 0x05, serial number: 0x03A2F413
Manufacturing date: Dec 2014
CID: 90014A48 34473164 040503A2 F413C104
CSD: D0270132 0F5903FF FFFFFFEF 8A4040D2
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 3.64 GiB(3,909,091,328 bytes)
Cache size: 512 KiB
Hardware reset function: 1
Partition configuration: 0x48
Boot acknowledge is sent during the boot operation
Boot partition 1 is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
Selected: [HYNIX] eNAND H9TP32A8JDACPR-KGM/4GB (BGA162)
i forget after save logos
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 8 bit (HS SDR 52MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: H4G1d (0x483447316404), rev: 0x05, serial number: 0x03A2F413
Manufacturing date: Dec 2014
CID: 90014A48 34473164 040503A2 F413C104
CSD: D0270132 0F5903FF FFFFFFEF 8A4040D2
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 3.64 GiB(3,909,091,328 bytes)
Cache size: 512 KiB
Hardware reset function: 1
Partition configuration: 0x48
Boot acknowledge is sent during the boot operation
Boot partition 1 is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
Selected: [HYNIX] eNAND H9TP32A8JDACPR-KGM/4GB (BGA162)
i forget after save logos
