UMT ★★★ Post All Successfully Repaired Phones Ultimate Multi Tool ★★★

[GsmToto]

Device : Samsung Galaxy S23 Ultra (SM-S918B) BIT-8
Operation : Reset FRP
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM5)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...Done
Protocol v3 or higher detected. Auto Loader unsupported.
Initializing Protocol...OK
Using Pre-Defined Loader [SM-S918B BIT-8.ufl]
Preparing Loader...Done
Sending Loader [SM-S918B BIT-8]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : , UFS, 512 GB
LU Count : 6 [0x076FA000] [0x00001400] [0x00001400] [0x00002000] [0x00028000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [65536], Out: 16384, Sector Size: 4096
Reading Partition Table...OK [99]
Reading Device Information...OK [Sign]
Build : S918BXXS8DYF2
Int. Build : SM-S918B_EUR_XX_QKEY1
boot.os_ver : 13
boot.sec_patch : 2025-06-01
sys.os_ver : 15
sys.sec_patch : 2025-06-01
vendor.os_ver : 13
vendor.sec_patch : 2025-06-01
Resetting FRP Lock...Failed
Using Patch Method... Done Done
Operation Finished.
QcFire Ver. 12.2

 

[GsmToto]

Brand/Model : *Auto* / *Auto Detect*
Operation : Erase Data + FRP
LOCAL SLA : ON
BOOT CFG : [EXPLOIT:PL][INFINIX V2]
Waiting for Device...Found
Port : MediaTek PreLoader USB VCOM (Android) (COM8)
Device Path : \\?\usb#vid_0e8d&pid_2000#6&236cc9f3&0&5#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
Driver : MediaTek Inc., 3.0.1512.0 [usb2ser.sys]
Mode : PRELOADER
Hw ID : MT6768 [0707] Helio P65/G85 k68v1
Details : 8A00,CA00,0000
Sec. Config : [SBA:ON] [SLA:OFF] [DAA:ON]
MEID : 84CDB56FF0F752AD5F2E79E8FF08A6C6
SoC ID[0] : 44B03DD25013C354ACD175F4981EC958
SoC ID[1] : 62376DC75A8A648536FE09DBA1627D2E
Sending 1st DA..OK
Jump DA Address...OK
Syncing...OK
Checksum Level is Storage
Connection : preloader
Speed : HIGH-SPEED
Reading RAM Configuration...OK
Running PL_EXPLOIT [1]...Done
Sending 2nd DA...OK
Local SLA (Generic)...OK
HRID : 49DC1A44661D095BDACDCC2A23F7E00B
RID : 49DC1A44661D095BDACDCC2A23F7E00B
Int. RAM : 0x0000000000070000 [448,00 KB]
Ext. RAM : 0x0000000100000000 [4,00 GB]
Flash ID : hC8aP>
CID : 90014A68433861503E02C9BCA18877B5
BOOT1 : 0x0000000000400000 [4,00 MB]
BOOT2 : 0x0000000000400000 [4,00 MB]
RPMB : 0x0000000001000000 [16,00 MB]
USERAREA : 0x0000000E8F800000 [58,24 GB]
PRE EOL : NORMAL
Life. Est.A : UNDEFINED
Life. Est.B : 20%-30% LIFE TIME USED
Reading Partition Table...OK
Manuf. : INFINIX MOBILITY LIMITED
Ven. Model : Infinix X682B
Platform : mt6768
Ven. Date : Fri Jul 29 23:47:55 CST 2022
Ver. Inc. : 220729V358
prd.os_ver : 10
prd.sec_patch : 2022-07-05
sys.os_ver : 10
sys.sec_patch : 2022-07-05
Bootloader : LOCKED
Erasing Userdata...OK
IMPORTANT : If phone reboots to recovery, simply Format from there.
Resetting FRP...OK
Operation Finished.
[UltimateMTK2 v2.6]

 

[GsmToto]

Samsung SM-A326B FRP removed in download mode

Model : MediaTek FRP
Operation : All MediaTek 2023
Searching for Phone...Found
Port: : COM4 : SAMSUNG Mobile USB Modem #9
Checking for Device...Found [Download Mode]
Reading Data from Phone...Done
Chipset : MT6853 [HiSpeed]
Closing Session...Done
Port: : COM8 : SAMSUNG Mobile USB Modem #9
Checking for Device...Found [Download Mode]
Resetting FRP Data...Done
Closing Session...Done
Operation Finished.
Elapsed Time 00:19
[UltimateSams v0.7]

 

[GsmToto]

Brand/Model : *Auto* / *Auto Detect*
Operation : Erase Data + FRP
LOCAL SLA : ON
BOOT CFG : [EXPLOIT:PL][INFINIX V1]
Waiting for Device...Found
Port : MediaTek PreLoader USB VCOM (Android) (COM10)
Device Path : \\?\usb#vid_0e8d&pid_2000#6&236cc9f3&0&5#{86e0d1e0-8089-11d0-9ce4-08003e301f73}
Driver : MediaTek Inc., 3.0.1512.0 [usb2ser.sys]
Mode : PRELOADER
Hw ID : MT6761 [0717] Helio A20/P22/A22/A25/G25
Details : 8A00,CA01,0200
Sec. Config : [SBA:ON] [SLA:OFF] [DAA:ON]
MEID : 92CBA5A0953FBB72D96A563EDF1B3583
SoC ID[0] : 73203B7C003EBC073A7523A25CE93700
SoC ID[1] : F1DB6B98FED22266A1FF4E2612B93858
Sending 1st DA..OK
Jump DA Address...OK
Syncing...OK
Checksum Level is Storage
Connection : preloader
Speed : HIGH-SPEED
Reading RAM Configuration...OK
Running PL_EXPLOIT [1]...Done
Sending 2nd DA...OK
Local SLA...OK
HRID : 2960F49C1E32CF4E6C7915AB4A3E4469
RID : 2960F49C1E32CF4E6C7915AB4A3E4469
Int. RAM : 0x000000000003A600 [233,50 KB]
Ext. RAM : 0x0000000080000000 [2,00 GB]
Flash ID : TJ3032
CID : 700100544A3330333201020989F4698F
BOOT1 : 0x0000000000400000 [4,00 MB]
BOOT2 : 0x0000000000400000 [4,00 MB]
RPMB : 0x0000000000400000 [4,00 MB]
USERAREA : 0x0000000748000000 [29,13 GB]
PRE EOL : NORMAL
Life. Est.A : 20%-30% LIFE TIME USED
Life. Est.B : 20%-30% LIFE TIME USED
Reading Partition Table...OK
And. Ver. : 11
Build Dt. : Fri Jan 12 15:35:34 CST 2024
Display ID : TECNO-RGo-32-240110V97
Ver. Inc. : 240112V566
Locale : en-US
Patch : 2024-01-01
dtbo.fprint : TECNO/BD4a-OP/TECNO-BD4a:11/RP1A.200720.011/240110V280
prd.fprint : TECNO/TSSI/AGo-32:11/RP1A.200720.011/240110V97
prd.os_ver : 11
prd.sec_patch : 2024-01-01
sys.fprint : TECNO/TSSI/AGo-32:11/RP1A.200720.011/240110V97
sys.os_ver : 11
sys.sec_patch : 2024-01-01
sys_ext.fprint : TECNO/TSSI/AGo-32:11/RP1A.200720.011/240110V97
sys_ext.os_ver : 11
sys_ext.sec_patch : 2024-01-01
Bootloader : LOCKED
Erasing Userdata...OK
IMPORTANT : If phone reboots to recovery, simply Format from there.
Resetting FRP...OK
Operation Finished.
[UltimateMTK2 v2.6]

 

[GsmToto]

Brand/Model : *Auto* / *Auto Detect*
Operation : Safe Format+FRP (Oppo)
LOCAL SLA : OFF
BOOT CFG : [EXPLOIT:BROM]
Waiting for Device...Found
Port : MediaTek PreLoader USB VCOM (Android) (COM7)
Device Path : \\?\usb#vid_0e8d&pid_2000#5&250b5bc3&0&2
#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
Driver : MediaTek Inc., 3.0.1512.0 [usb2ser.sys]
Mode : PRELOADER
Force Enter BROM...OK
Hw ID : MT6765 [0766] Helio P35/G35
Details : 8A00,CA00,0000
Sec. Config : [SBA:True] [SLA:False] [DAA:False]
MEID : 32D6DA4545D7BD39EEBFDCE2A3A3DC11
SoC ID[0] : 1599D95476366AF19CD3DF159C4C10F5
SoC ID[1] : 0A82831C8985321933FE324880C2EB3F
Running Exploit...Done
Downloading Preloader...OK
PRELOADER : preloader_v820.bin
Sec. Config : [SBA:OFF] [SLA:OFF] [DAA:OFF]
[INTERNAL] DA Selected!
DA Security Patched
Sending 1st DA...OK
Jump DA Address...OK
Syncing...OK
Checksum Level is Storage
Connection : brom
Speed : HIGH-SPEED
Reading RAM Configuration...OK
Reading EMI Configuration...OK
CID : D601034133413434321028CEC524C849 [EMMC]
Initializing Storage...OK
Sending 2nd DA...OK
Initialize DA Extension...OK
HRID : 57FBCD633E25B6DC0A417E0597F6455C
RID : 57FBCD633E25B6DC0A417E0597F6455C
Int. RAM : 0x0000000000038000 [224,00 KB]
Ext. RAM : 0x0000000100000000 [4,00 GB]
Flash ID : A3A442
CID : D601034133413434321028CEC524C849
BOOT1 : 0x0000000000400000 [4,00 MB]
BOOT2 : 0x0000000000400000 [4,00 MB]
RPMB : 0x0000000001000000 [16,00 MB]
USERAREA : 0x0000001CCF000000 [115,23 GB]
PRE EOL : NORMAL
Life. Est.A : 0%-10% LIFE TIME USED
Life. Est.B : UNDEFINED
Reading Partition Table...OK
Brand : WIKO
Manuf. : WIKO
Model : VHEM
Device : VHEM
And. Ver. : 12
Prod. Name : VHEM
Build Dt. : Thu Jun 16 23:39:08 CST 2022
Display ID : SP1A.210812.016 release-keys
Ver. Inc. : 1655393948
Patch : 2022-05-05
dtbo.fprint : WIKO/VHEM/VHEM:12/SP1A.210812.016/1654183838
prd.fprint : WIKO/VHEM/VHEM:12/SP1A.210812.016/1654183838
prd.os_ver : 12
prd.sec_patch : 2022-05-05
sys.fprint : WIKO/VHEM/VHEM:12/SP1A.210812.016/1654183838
sys.os_ver : 12
sys.sec_patch : 2022-05-05
Bootloader : LOCKED
Resetting FRP...OK
Executing Safe Format (Oppo)...Done
If phone stuck on recovery, try [Fix Recovery].
Operation Finished.
[UltimateMTK2 v2.4]
Log Saved : 20485901_076924.log

 

[GsmToto]

Device : Samsung Galaxy A52s 5G (SM-A528B) BIT-B
Operation : Samsung Reset FRP
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
SAMSUNG : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL DOWN + POWER on phone more than 3 times rapidly and then leave EDL Cable Button.
SAMSUNG (NEW) : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL UP + DOWN on phone more than 3 times rapidly and then leave EDL Cable Button.
OPPO/REALME : Use Vol Down + Power to Enter Recovery > Select Language > Connect Cable
then tap 3 times on Version shown at bottom center > Click Yes.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM3)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.5.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Protocol Ver. : 2
Hardware ID : E1201900 [SM7325] 00002000
OPK_DATA : 1A9F05BA6F39A9DF2A6B2377A5889A262DA2523DC5AC3DB0DE CA78F44B211CBA
Initializing Protocol...OK
Using Pre-Defined Loader [SM-A528B BIT-B.ufl]
Preparing Loader...Done
Sending Loader [SM-A528B BIT-B]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : SM7325, UFS, 128 GB
LU Count : 6 [0x01DA8C00] [0x00000800] [0x00000800] [0x00000400] [0x00020000] [0x00000800]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [65536], Out: 16384, Sector Size: 4096
Reading Partition Table...OK [77]
Reading Device Information...OK
Software : UP1A.231005.007.A528BXXSBGYC1, A528BXXSBGYC1 [Mon Mar 31 14:48:28 KST 2025]
Android Ver. : 14
Patch Level : 2025-04-01
boot.os_ver : 11
boot.sec_patch : 2025-04-01
sys.os_ver : 14
sys.sec_patch : 2025-04-01
vendor.os_ver : 11
vendor.sec_patch : 2025-04-01
Reset FRP... Done
Operation Finished.
QcFire Ver. 12.4
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM38)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.5.2
Opening Port...OK
Rebooting Device...Done

 

[GsmToto]

Brand/Model : *Auto* / *Auto Detect*
Operation : META Functions (Enable ADB (Infinix))
Checking for exisitng device in META mode...No Device!
Waiting for Device...Found
Mode : PRELOADER
Port : MediaTek PreLoader USB VCOM_V1632 (Android) (COM3)
Connecting Device...OK
Waiting for Device [META]...OK
Port : MediaTek USB VCOM (Android) (COM4)
Brand : Infinix
Model : Infinix X6531
Market Name : unknown
Market Name : unknown
Manufac. : INFINIX
Build Date : Sat Jun 28 16:44:48 CST 2025
Ven. Date : Sat Jun 28 15:53:03 CST 2025
Platform : MT6768
OEM : unknown
OEM Device : unknown
Disp. ID : X6531-V631APQRSTUVWXYZZAaAbAcAd-U-OP-250628V3133
Inc. Ver. : 250628V2880
Patch Level : 2025-07-05
OTA Ver. : unknown
BRAND : Infinix
MODEL : Infinix X6531
BUILD : X6531-V631APQRSTUVWXYZZAaAbAcAd-U-OP-250628V3133
BUILD DATE : Sat Jun 28 16:44:48 CST 2025
Enabling ADB...Done
Operation Finished.
[UltimateMTK2 v2.7]
Log Saved : 20250920_161759.log

Brand/Model : Infinix/Tecno/iTel (ADB)
Operation : Reset FRP (ADB)
Searching for Device..Found
Brand : Infinix
Model : Infinix X6531
Android Ver. : 14
Build : X6531-V631APQRSTUVWXYZAaAbAcAd-U-OP-250628V3133
Build Date : Sat Jun 28 16:44:48 CST 2025
Patch Level : 2025-07-05
Bootloader : unknown
Resetting FRP Lock...Done
Operation Finished.
[UltimateMTK2 v2.7]
Log Saved : 20275790_165672.log
done

 

[.::Greed::.]

Operation : Format FS 2 (Vivo)
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
SAMSUNG : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL DOWN + POWER on phone more than 3 times rapidly and then leave EDL Cable Button.
SAMSUNG (NEW) : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL UP + DOWN on phone more than 3 times rapidly and then leave EDL Cable Button.
OPPO/REALME : Use Vol Down + Power to Enter Recovery > Select Language > Connect Cable
then tap 3 times on Version shown at bottom center > Click Yes.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM9)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.3.5
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Protocol Ver. : 2
Hardware ID : E1A00900 [8953] 00000000
OPK_DATA : 30315EBED1DD09CEAAE927CAE0EE967076BC178CA33718DB4FFF8F02A0E7FAD2
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8953_003]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : 8953, EMMC, 64 GB
LU Count : 3 [0x0747C000] [0x00002000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK [54]
Reading Device Information...OK
Device : vivo vivo 1716 [msm8953] [msm8953_64]
Brand : vivo
Prod.Name : msm8953_64
Software : OPM1.171019.026 release-keys, eng.compil.20230605.220918 [Mon Jun 5 22:09:18 CST 2023]
Android Ver. : 8.1.0
Patch Level : 2020-10-01
Preparing Data...Done
Formatting Userdata......Done
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 12.2

 

[iwanazzam]

x6880 done

 

[GsmToto]

Brand/Model : Auto / Auto Detect
Operation : Safe Format+FRP
LOCAL SLA : ON
BOOT CFG : [EXPLOIT:BROM]
Waiting for Device...Found
Port : MediaTek USB Port (COM31)
Device Path : \\?\usb#vid_0e8d&pid_0003#6&323149bf&0&2#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
Driver : MediaTek Inc., 3.0.1512.0 [usb2ser.sys]
Mode : BROM
Hw ID : MT6739 [0699] MT6739/MT6731/MT8765
Details : 8A00,CA00,0000
Sec. Config : [SBA:False] [SLA:False] [DAA:False]
MEID : E623DC6F303BF0961B5651E8D350E7D3
SoC ID[0] : D87BC1576F172B8742663DACF273CFFF
SoC ID[1] : C0B3B7AEF4AEAEAC914AF38671A02C07
Running Exploit...Done
Downloading Preloader...OK
PRELOADER : preloader_k31v1_bsp_512.bin
Sec. Config : [SBA:OFF] [SLA:OFF] [DAA:OFF]
[INTERNAL] DA Selected!
DA Security Patched
Sending 1st DA...OK
Jump DA Address...OK
Syncing...OK
Checksum Level is Storage
Connection : brom
Speed : HIGH-SPEED
Reading RAM Configuration...OK
Reading EMI Configuration...Failed/Unsupported
Initializing Storage...OK
Sending 2nd DA...OK
Initialize DA Extension...OK
RID
Int. RAM : 0x0000000000020000 [128.00 KB]
Ext. RAM : 0x0000000040000000 [1024.00 MB]
Flash ID : F722MB
CID : 150100463732324D420099921512B75D
BOOT1 : 0x0000000000400000 [4.00 MB]
BOOT2 : 0x0000000000400000 [4.00 MB]
RPMB : 0x0000000000080000 [512.00 KB]
USERAREA : 0x00000001D2000000 [7.28 GB]
PRE EOL : UNDEFINED
Life. Est.A : UNDEFINED
Life. Est.B : UNDEFINED
Reading Partition Table...OK
Brand : Digit
Manuf. : Digit
Model : Digit4G Energy
Device : Digit4G_Energy
And. Ver. : 8.1.0
Prod. Name : Digit4G_Energy
Build Dt. : Fri Nov 17 11:33:05 CST 2023
Display ID : DigitOS8-M42868DG-V21-20231117-1132
Ver. Inc. : 1700191987
Locale : en-US
Patch : 2021-08-05
Bootloader : LOCKED
Resetting FRP...OK
Executing Safe Format...Done
If phone stuck on recovery, try [Fix Recovery].
Operation Finished.
[UltimateMTK2 v2.8]
Log Saved : 20251017_231251.log*

 

[GsmToto]

Start Connect v3.00
Selected config: Vivo/2024-11-v5 Boot [DA] Factory v7
Port: BROM + PL; Force BROM: 0; USB High-Speed: On
DA Key: custom; LSLA: On; Auto-EMI: On
Power device Off and connect cable now
Remember Volume Up/Down or Test-Point
Waiting for device...
[ PRELOADER #25 ] MediaTek PreLoader USB VCOM (Android) (COM25) 0E8D:2000
Waiting for boot Ack...
Handshake... Ok
MT6765 HWs: 8A00 HWv: CA00 HWc: 0766 SWv: 0000 Evo: 0000 Helio Cervino|P35|G35|G36|G37|G50 Type: [Raphael]; FireFly [FF] support: Yes
Sec: 0x0005 SBC+SDA; BROM/BL ver: 0xFF/0x03 [PRELOADER]
MEID: D0991D39BCBE9D7D0C6F2A64992F2E3A
SOCID: 7C1543F77E5DC5779D235C4449ABF92EC6B99355709CA4B879ADAFC9E8779BBE
[d316571a] C:\InfinityBox\CM2MT2\boot\Vivo\2024-11-v5\MTK_AllInOne_DA.2024-11.a6947361.bin
Looking for bootcode... Ok
DA vendor: bbk
Send DA1... Ok [Adjusted 1|2: Untold|Untold]
Jump to DA... Ok
Sync... Ok
DA sync... Ok
Set PowerKey... Ok
Set PowerSource... Ok
Set ChecksumLevel [none]... Ok
DA set params... preloader EXT_RAM initialized
Boot DA2/1...
Boot DA2/2... Ok [Adjusted 1|2: Untold|Untold]
DA sync... Ok
DA Auth no need
Get hardware info...
SRAM: 0x0003A000 232.00 Kb
DRAM: 0xC0000000 3.00 Gb

EMMC CID: 9B010059325030333200E50F3FF349F5 crc Ok
Vendor: Hynix OEM: 0x0100 ID: 593250303332 [Y2P032] PRV: 0x00 Serial: 3842981875 0xE50F3FF3
MM/YY: 4/2022
BOOT1: 0x00400000 4.00 Mb
BOOT2: 0x00400000 4.00 Mb
RPMB: 0x01000000 16.00 Mb
USER: 0x747C00000 29.12 Gb

MT6765 HWs: 8A00 HWv: CA00 HWc: 0766 SWv: 0000 Evo: 0000 Helio Cervino|P35|G35|G36|G37|G50 Type: [Raphael]; FireFly [FF] support: Yes
MEID: D0991D39BCBE9D7D0C6F2A64992F2E3A
SOCID: 7C1543F77E5DC5779D235C4449ABF92EC6B99355709CA4B879ADAFC9E8779BBE
HRID: B028B8C90D967C4971DF8CA4210A5D7E
RNID: BBE1878D9C535D125655B7EFA038575A sync2 delayed
USB: HIGH-SPEED
[Adjusted 1|2: Untold|Untold, Allow errors: No, Collision: 82|4]
Boot done 4 sec

[ff3] run warn(50)
da3 can't start. Select another DA (f.e. base/2316) or use Boot [FF] FireFly
EMMC Life Ok

RPMB engine Off. Another DA selection may helps
Get 1st partition table... 64 Ok 218 us GPT Ok
PGPT 53 entries

Read [preloader]... Ok 125 us
preloader (0) MT6765 preloader_k65v1_64_bsp.bin with 11 memory types [315236aa] slots: no
Read [preloader_backup]... Ok 125 us
preloader (1) MT6765 preloader_k65v1_64_bsp.bin with 11 memory types [315236aa] slots: no
Device has no slots
Probe LK...
lk [2649ea12] k65v1_64_bsp-ed70c6a-20240202103534-20250304172247

Probe boot...
recovery_vendor;ramsidk size=0;recovery_ramdisk;ramsidk size=0;vendor_boot;ramsidk size=0;recovery;gzip;ramdisk size 74.87 Mb;2 found
boot;gzip;ramdisk size 2.47 Mb;1 found Ok 1 sec
Probe vbmeta... Ok(4) 703 us
Product Brand: vivo
Product Device: V2204
Product Model: V2204
Product Name: V2204
SW: vivo/V2204/V2204:12/SP1A.210812.003/compiler03041714:user/release-keys
Patch Level: SP1A.210812.003
Display ID: PD2216F_EX_A_12.0.36.0.W20.V000L1
SW Version: compiler03041714
Ver. CodeName: REL
Sec. Patch: 2025-03-01
Build Time: 04/03/2025 09:10:52
Product Info: k65v1_64_bsp
SW: full_k65v1_64_bsp-user 12 SP1A.210812.003 compiler03041714 release-keys
Vivo OS: Funtouch OS 12 Global
Vivo Product: V2204
Vivo HW: PD2216F_EXMA
Product Manfct: vivo
Build: vivo/V2204/V2204:12/SP1A.210812.003/compiler03041714:user/release-keys
Product Board: k65v1_64_bsp
Board Platform: mt6765
ID: vivo-v2204-k65v1-64-bsp
Strategy [vivo]
Firmware ID: MT6765_vivo_V2204_OSv12_PD2216F_EX_A_12.0.36.0.W20.V000L1_SP1A.210812.003_k65v1_64_bsp
Android ver: 12
userdata: [ext4] FBE [file based encryption] cache: [ext4]
Verify firmware [MT6765_vivo_V2204_OSv12_PD2216F_EX_A_12.0.36.0.W20.V000L1_SP1A.210812.003_k65v1_64_bsp]... Firmware is unknown
Please upload Flash Files Database - iosFileUploader - Infinity Box Dongle #CM2 [BEST] Support 2 sec

Load userdata... Ok 15 us
userdata: 19.13 Gb [FS unknown|raw] encrypted

Backup exist: C:\InfinityBox\CM2MT2\backup\MT6765__D0991D39BCBE9D7D0C6F2A64992F2E3A_vivo-v2204-k65v1-64-bsp.7z

Load nvram...
NVRAM seems as damaged
PSN1: 0B1A335589531801
PSN2: N/A

get modem info... nothing
Secondary RPMB... absent
Probe FRP... Most probably Off
Probe bootloader...
Bootloader locked, oem|U, flag 0x01
Stop [Job 25988645] Connect v3.00 37 sec => keep connection

 

[GsmToto]

Operation : Reset FRP
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
SAMSUNG : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL DOWN + POWER on phone more than 3 times rapidly and then leave EDL Cable Button.
SAMSUNG (NEW) : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL UP + DOWN on phone more than 3 times rapidly and then leave EDL Cable Button.
OPPO/REALME : Use Vol Down + Power to Enter Recovery > Select Language > Connect Cable
then tap 3 times on Version shown at bottom center > Click Yes.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM44)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.7
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Protocol Ver. : 2
Hardware ID : E1A00900 [8953] 65001500
OPK_DATA : 3B48AE9023196AE5C8162BCE65CB66E9636C784CB52A55046D 15110FD8B11688
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8953_030]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : 8953, EMMC, 32 GB
LU Count : 3 [0x03A3E000] [0x00002000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [4096], Out: 16384, Sector Size: 512
Reading Partition Table...OK [57]
Reading Device Information...OK
Device : unknown
Software : System 8.2.0.036(2E2Y) [Thu Aug 12 15:30:59 CST 2021]
Android Ver. : 8.1.0
Patch Level : 2020-09-01
Resetting FRP Lock.......Done
Operation Finished.

 

[GsmToto]

Brand/Model : *Auto* / *Auto Detect*
Operation : META Functions (Reset FRP (Infinix/Tecno))
Checking for exisitng device in META mode...No Device!
Waiting for Device...Found
Mode : PRELOADER
Port : MediaTek PreLoader USB VCOM_V1632 (Android) (COM13)
Connecting Device...OK [SLA] Auth OK
Waiting for Device [META]...OK
Port : MediaTek USB VCOM (Android) (COM14)
Brand : TECNO
Model : TECNO BF7
Market Name : unknown
Market Name : unknown
Manufac. : TECNO
Build Date : Tue Aug 22 05:42:10 CST 2023
Android : 12
Ven. Date : Tue Aug 22 04:50:51 CST 2023
Platform : MT6761
OEM : unknown
OEM Device : unknown
Disp. ID : BF7-H6127ABCDSTUAdAeAfArAs-S-GL-230822V1621
Inc. Ver. : 230822V1327
Patch Level : 2023-07-05
OTA Ver. : unknown
Serial : unknown
BRAND : TECNO
MODEL : TECNO BF7
BUILD : BF7-H6127ABCDSTUAdAeAfArAs-S-GL-230822V1621
BUILD DATE : Tue Aug 22 05:42:10 CST 2023
Reading Partition Data...Done
Total 50 Partitions Found.
Resetting FRP Lock...Done