★★ Post Here All Successful Stories By Infinity-Box CM/CM2- ★★

[niloy2007]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 21 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0000
BB_CPU_SN : D66DD57BBA58CDEB57CBCC7294B90EBE
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : C800 6000 1700 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00ED , [GigaDevice] GD25LQ64
[0] : FLASH_DIE : 00C8 0060 0017 0000
[0] : FLASH_LEN : 0x00800000
INT_RAM : 0x0000D000
EXT_RAM : 0x00800000

Backup done
Executing FFS FORMAT now...
FAT_RANGE : 0x00730000-0x007FFFFF , LEN : 0x000D0000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE

Done!
Elapsed: 00:00:24
Reconnect Power/Cable!

Finish at : [4/6/2019 / 7:09:48 PM]

 

[niloy2007]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:57
Reconnect Power/Cable!

Finish at : [4/3/2019 / 8:52:19 PM]

Start at : [4/3/2019 / 8:52:26 PM]
Operation : Flash [ v1.58 ]

======= Flash

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 20 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 520001154D42313238B906425D8002CE
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMB12
[eMMC] : FLASH_CID : 150100523231424D4206B938CE02235D
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x0000000747C00000
[eMMC] : FLASH_UCP : 29820 MiB [eMMC 32 GiB]
DEV RID : 0xD5575D40792876039CDC9CE3872B2547
INT RAM : 0x00020000
EXT RAM : 0xC0000000 [3 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6735 , Project : gnbj6735_65c_l1 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 4218 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001C80000-0x0000000004D80000
Erase : 0x0000000006B00000-0x0000000740080000
Flash Pre-Erase Done, time used : 00:00:01

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_gnbj6735_65c_l1.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0016
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : TEE1
Image Flash Ok
Flash now : TEE2
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:05:35

Processing : Verify
Verify Passed : LK
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : LOGO
Verify Passed : SECRO
Verify Passed : TEE1
Verify Passed : TEE2
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:01:16

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:07:33
Reconnect Power/Cable!

Finish at : [4/3/2019 / 8:59:56 PM]

 

[niloy2007]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 155 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 484A019061344741600AA532FD39E62C
Initialize Memory ...
DRAM configured from IDB!
DRAM initialize passed!
DRAM size : 0x80000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , 2a4GA
[eMMC] : FLASH_CID : 90014A484147346132A50A602CE624FD
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003AB400000
[eMMC] : FLASH_UCP : 15028 MiB [eMMC 16 GiB]
DEV RID : 0xD5575D40611B9AF2E719F2DEF88755E1
INT RAM : 0x00020000
EXT RAM : 0x80000000 [2 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!

Done!
Elapsed: 00:00:25
Reconnect Power/Cable!

Finish at : [4/3/2019 / 5:29:02 PM]

 

[niloy2007]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 155 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0000
BB_CPU_SN : BDFF1B826A2115B752ABDE081762D28F
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : EF00 6000 1700 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00DF , [WINBOND] W25Q64DW
[0] : FLASH_DIE : 00EF 0060 0017 0000
[0] : FLASH_LEN : 0x00800000
INT_RAM : 0x0000D000
EXT_RAM : 0x00800000

Backup done
Executing FFS FORMAT now...
FAT_RANGE : 0x00730000-0x007FFFFF , LEN : 0x000D0000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE

Done!
Elapsed: 00:00:20
Reconnect Power/Cable!

Finish at : [4/3/2019 / 4:56:56 PM]

 

[niloy2007]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 20 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 484A019065314738C0FB07055D08226C
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A48384731650507FBC06C22925D
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0xD5575D4073B5581B529340C124509BC1
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6735 , Project : bird6735m_35gu_a_l , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3981 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 1
Erase : 0x0000000001C80000-0x0000000142380000
Flash Pre-Erase Done, time used : 00:00:03

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0016
Update PMT by user request
[SpecOp] : Extend UserArea
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : TEE1
Image Flash Ok
Flash now : TEE2
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:05:36

Processing : Verify
Verify Passed : LK
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : LOGO
Verify Passed : SECRO
Verify Passed : TEE1
Verify Passed : TEE2
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:01:38

Update Mirror PMT
[SpecOp] : Extend UserArea
Update Done!

Update RomInfo done

Done!
Elapsed: 00:07:48
Reconnect Power/Cable!

Finish at : [4/2/2019 / 8:18:55 PM]

 

[niloy2007]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 20 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6737
BB_CPU_NME : [MediaTek] MT6737M|MT6737_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 5300011F3038504800004A38B93AE80C
[WARNING] : MEMORY_eMMC_VALIDATE_FAILED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x1F , OEM : 0100
[eMMC] : FLASH_INF : [NOT_IN_BASE] , 808PH
[eMMC] : FLASH_CID : 1F01005348503830384A00000CE823B9
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000001BB000000
[eMMC] : FLASH_UCP : 7088 MiB [eMMC 8 GiB]
DEV RID : 0xD5575D404304B4A891FC2F854F373161
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:52
Reconnect Power/Cable!

Finish at : [4/1/2019 / 1:13:40 PM]

 

[niloy2007]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 21 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6737
BB_CPU_NME : [MediaTek] MT6737M|MT6737_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 460001154D323237F4E10042A32AA8C8
Initialize Memory ...
DRAM configured from IDB!
DRAM initialize passed!
DRAM size : 0x40000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM227
[eMMC] : FLASH_CID : 150100463732324D4200E1F4C8A893A3
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0xD5575D40F6F50E7BFDFB96A5FF8066A9
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!

Done!
Elapsed: 00:00:20
Reconnect Power/Cable!

Finish at : [3/28/2019 / 8:05:32 PM]

 

[niloy2007]

NOKIA 5.1 FRP

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone

- > Info : Press and hold BOTH volume keys, if device boot fail at BROM stage!

Waiting for device connection ...

PTFN : MediaTek USB Port (COM9)
MODE : BOOTROM
PORT : 9
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : DSLevel : DEV_KEY+DEV_ARB
BROM : BOOTROM
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 0000 0000 [0200] V0: 0000 0000 [0001]
BROM : SOCID : F79B50AE44D888C705A8C238FE5D3F327BD5C0F523881166AFAB7E24E7E064BD
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6771
AGENT : Nokia DownloadAgent ver.07220419 BEST2
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

EMMC: 150100474436424D420142849B47954D
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : GD6BMB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : C9D4C4DC40A6138C60BC258766FF1D6B

DA : USB : HIGH-SPEED

Boot done!

Format Ok : USERDATA
Format Ok : RESET PROTECTION

Done!
Elapsed: 00:01:32

Reconnect Power/Cable!

 

[Deepesh Sharma]

Micromax Q380 Flashing Done

 

[nasiraslam]

Qmobile infinity F mt6580 read flash done with cm2

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone

Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM_V1632 (Android) (COM13)
MODE : PRELOADER PORT
PORT : 13
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : PRELOADER PORT
MODE : 0_base : BASE_v1712 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6580
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 484A019061344741CB0DA53223A30E38
DAInf: 4 : 2 : 156
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 90014A484147346132A50DCB380EA323
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : HAG4a2
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3AB400000 [ 14.68 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0x80000000 [ 2.00 GB ]

CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : C2988B9BF978115862A622EC6BF940

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : HIGH-SPEED

Boot done!

Patch Level : MRA58K
Display ID : MRA58K release-keys
Ver. CodeName : REL
Ver. Release : 6.0
Sec. Patch : 2017-01-05
Build Time : 1554687505
Product Model : Q Infinity F
Product Brand : O1
Product Name : Q Infinity F
Product Device : Q_Infinity_F
Product Board : Q Infinity F
Product Manfct : Q Infinity F
Board Platform : mt6580
Product Info : zechin6580_weg_m

MT6580__Q_Infinity_F__Q_Infinity_F__6.0__MRA58K__zechin6580_weg_m

SecureDevice : Plain

Read : preloader.bin
Read : proinfo.img
Read : nvram.bin
Read : lk.bin
Read : boot.img
Read : recovery.img
Read : logo.bin
Read : secro.img
Read : system.img
ExtSparse : Compression ratio : 8%
Read : cache.img
Read : userdata.img

FW Size : 1.64 GB
Android Info saved : _Android_info.txt
Scatter : MT6580_Android_scatter.txt
Saved to : C:\Users\ideal\Desktop\MT6580__Q_Infinity_F__Q_Infinity_F__6.0__MRA58K__zechin6580_weg_m\

Done!
Elapsed: 00:06:44

 

[shakir77]

Nokia TA-1034 MTK6261 Read Flash With CM2

View attachment 4104

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 67 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0000
BB_CPU_SN : B82FC3ECFB99B49C53164F4A76D8CBA7
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00EC , [GigaDevice] GD25LQ32
[0] : FLASH_DIE : 00C8 0060 0016 0000
[0] : FLASH_LEN : 0x00400000
INT_RAM : 0x0000D000
EXT_RAM : 0x00400000
Reading Flash Content now ...

Read Flash now
Read Ok , 4194304 bytes read
Check and collect compile info
File_Info : M105_61D_PCB01_gprs_MT6261_S00.N105_IC_N_H_U_180930_V02.bin
FileVersion : N105_IC_N_H_U_180930_V02
Saved to : C:\InfinityBox\CM2MTK\Read_out\M105_61D_PCB01_gprs_MT6261_S00.N105_IC_N_H_U_180930_V02.bin

Done!
Elapsed: 00:00:16
Reconnect Power/Cable!

dear bro i need this file .plz upload link .jazakAllah

 

[Deepesh Sharma]

Gionee F103 Remove Frp LOck

Please login to view image

 

[Deepesh Sharma]

Gionee F103 Stuck On Logo Solved

Please login to view image

 

[Deepesh Sharma]

Intex aqua air Read User Code

Please login to view image

 

[Akhtar Ali Jatt]

Qmobile i6 metal One Format Done

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone

Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM264)
MODE : PRELOADER PORT
PORT : 264
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : PRELOADER PORT
MODE : 0_base : BASE_v1712 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6580
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 484A019065314738D42A0705DF24765C
DAInf: 4 : 2 : 156
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 90014A48384731655072AD45C7624DF
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : H8G1e
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x1D2000000 [ 7.28 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0x40000000 [ 1.00 GB ]

CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : BF8A1B2BF68D6164A9BC1946E3FD32AA

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : HIGH-SPEED

Boot done!

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION
Format Ok : USERDATA

Done!
Elapsed: 00:00:28

Reconnect Power/Cable!

 

[Akhtar Ali Jatt]

VgoTel i251 Read User Code Done

Operation : Read UserCode [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 255 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0000
BB_CPU_SN : 19C967E88DC107CED755272B5FABAF48
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x0112 , [MXIC] MX25L3291FWJI_09
[0] : FLASH_DIE : 00C2 0020 0016 0000
[0] : FLASH_LEN : 0x00300000
SDS_INFO : 0x002FE000 , 0x00002000
INT_RAM : 0x0000D000
EXT_RAM : 0x00400000

Read ExtData
Sorting ExtData
Reading UserCode

Active : Yes , Code : 225588

PLock|MobTrack : Not active

Done!
Elapsed: 00:00:03
Reconnect Power/Cable!

 

[Akhtar Ali Jatt]

VgoTel i251 Read
Operation : Read UserCode [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 255 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0000
BB_CPU_SN : 19C967E88DC107CED755272B5FABAF48
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x0112 , [MXIC] MX25L3291FWJI_09
[0] : FLASH_DIE : 00C2 0020 0016 0000
[0] : FLASH_LEN : 0x00300000
SDS_INFO : 0x002FE000 , 0x00002000
INT_RAM : 0x0000D000
EXT_RAM : 0x00400000

Read ExtData
Sorting ExtData
Reading UserCode

Active : Yes , Code : 225588

PLock|MobTrack : Not active

Done!
Elapsed: 00:00:03
Reconnect Power/Cable!

 

[Akhtar Ali Jatt]

Qmobile S1 Lite Format Done


Operation : Format FS / Reset Settings [ v2.01 ]
Mode : Default [ Reset Settings + FRP ]

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731x_BASE : SC7731C_eMMC_1GB_NS
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : TRCC not supported!
FDL : Control transfered!

Boot Done!

Wipe Ok : UserData
Wipe Ok : Cache
Wipe Ok : FRP

Reconnect Power/Cable!


Done!
Elapsed: 00:00:41

 

[Akhtar Ali Jatt]

VGOTEL OCEAN 6 Format Done


Operation : Format FS / Reset Settings [ v2.01 ]
Mode : Default [ Reset Settings + FRP ]

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731x_BASE : SC7731C_eMMC_1GB_NS
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : TRCC not supported!
FDL : Control transfered!

Boot Done!

Wipe Ok : UserData
Wipe Ok : Cache
Wipe Ok : FRP

Reconnect Power/Cable!


Done!
Elapsed: 00:00:47

 

[Akhtar Ali Jatt]

Qmobile G5 Format Done

Operation : Format FileSystem [ v1.04 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource : InternalLibrary
BootVersion : Infinity SCR 653x NOR v1.3(c)2019
Port speed : 921600
FDL Flash : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_0F972D9A1D81_NVM.nv

Executing FormatFFS ...
Format FFS Done!

Done!
Elapsed: 00:00:20

Reconnect Power/Cable!